GOST R 51701-2000
ГОСТ Р 51701-2000
|
|
Connecting devices. Devices for the connection of aluminium conductors in clamping units of any material and copper conductors in aluminium bodied clamping units. General requirements and methods of tests
Соединительные устройства. Устройства для присоединения алюминиевых проводников к зажимам из любого материала и медных проводников к зажимам из алюминиевых сплавов. Общие требования и методы испытаний
Status: Not effective - Canceled. Registration information 859-st dated November 15, 2012 (official website of Rosstandart); IUS 10-2013
The standard applies to screw and screwless contact clips of connecting devices from any material, made both at the same time with the device, and built into the device, designed to connect aluminum conductors without special training (with insulated or non-insulated ends), clad with copper (in accordance with IEC 228 [1], rigid (single and stranded), with a nominal cross section of 2.5 to 50 mm2 inclusive and equivalent AWG conductors for a rated alternating voltage up to 1000 V and frequencies up to 1000 Hz, turn on Flax and constant voltage up to 1500 V. The standard also applies to clamps with an aluminum alloy housing for connecting rigid (single and stranded) and flexible copper conductors (in accordance with IEC 228) [1]) with a nominal cross section of 0.5 to 35 mm2 inclusive and equivalent AWG conductors.
Стандарт распространяется на винтовые и безвинтовые контактные зажимы соединительных устройств из любого материала, выполненных как заодно с прибором, так и встроенными в прибор, предназначенные для присоединения алюминиевых проводников без специальной подготовки (с изолированными или неизолированными концами), плакированных медью (в соответствии с МЭК 228 [1], жестких (одно- и многожильных), номинальным сечением от 2,5 до 50 мм2 включительно и эквивалентных проводников AWG на номинальное переменное напряжение до 1000 В частоты до 1000 Гц включительно и постоянное напряжение до 1500 В. Стандарт распространяется также на зажимы с корпусом из алюминиевых сплавов для присоединения жестких (одно- и многожильных) и гибких медных проводников (в соответствии с МЭК 228) [1]) номинальным сечением от 0,5 до 35 мм2 включительно и эквивалентных проводников AWG.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Gosstandart of Russia,
12/26/2000
SKU: RUSS71271
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
29 Electrical Engineering »
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Welding materials »
Welding regulations »
Documentation »
Welding regulations »
Mechanical Testing »
Welding regulations »
Welding work »
Soldering »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Non-ferrous metals »
Welding regulations »
Welding materials »
Solders »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
004/2011 TR CU. About safety of low voltage equipment »
Regulations and standards (to TR CU 004/2011) »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.15 Testing and control of products of electronic, optical and electrical industry »
4.15.1 Electric machines, electrical equipment and materials »
ISO classifier »
29 ELECTRICAL ENGINEERING »
29.120 Electrical fittings »
29.120.20 Connecting devices »
National standards »
29 ELECTRICAL ENGINEERING »
29.120 Electrical fittings »
29.120.20 Connecting devices »
ISO classifier »
29 ELECTRICAL ENGINEERING »
29.120 Electrical fittings »
29.120.30 Plugs, sockets, connectors »
National standards »
29 ELECTRICAL ENGINEERING »
29.120 Electrical fittings »
29.120.30 Plugs, sockets, connectors »
National Standards for KGS (State Standards Classification) »
Latest edition »
E Power and electrical equipment »
E7 Electrical apparatus and fittings »
E71 Devices with voltage up to 1000 V »
National Standards for OKSTU »
ELECTRICAL EQUIPMENT AND MATERIALS »
Apparatus for the distribution of electrical energy (except for automatic switches) »
The Document References:
GOST 15.001-88: System of product development and launching into manufacture. Products of industrial and technical designation
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15543.1-89: Electrical articles. General requirements for environmental climatic aspects stability
GOST 16504-81: The state system of testing products. Product test and quality inspection. General terms and definitions
GOST 17516.1-90: Electrical articles. General requirement for environment mechanical stability
GOST 22483-77: Copper and aluminum conductors
GOST 23216-78: Electrotechnical products. Storage, transportation, temporary corrosion protection and packing. General requirements and test methods
GOST 27.003-90: Reliability in engineering. Make-up and general rules for assigning reliability requirements
GOST 27.410-87: Industrial product dependability. Inspection methods of reliability indices and plans of check tests on reliability
GOST 8724-2002: Basic norms of interchangeability. Metric screw threads. General plan
GOST 8724-81: Basic norms of interchangeability. Metric screw thread. Diameters and pitches
GOST 9.005-72: Unified system of corrosion and ageing protection. Metals, alloys, metallic and non-metallic coatings. Permissible and impermissible contacts with metals and non-metals
GOST R 50030.7.1-2000: Low-voltage switchgear and controlgear. Part 7. Ancillary equipment. Section 1. Terminal blocks for copper conductors
GOST R 50043.1-92: Connecting devices for low voltage circuits for household and similar purposes. Part 1. General requirements
GOST R 50043.2-92: Connecting devices for low voltage circuits for household and similar purposes. Part 2-1. Particular requirements for connecting devices as separate entities with screw-type clamping units
GOST R 50043.4-2000: Connecting devices for low voltage circuits for household and similar purposes. Part 2-3. Particular requirements for connecting devices as separate entities with insulation piercing clamping units
GOST R 51322.1-99: Plugs and socket-outlets for household and similar purposes. Part 1. Requirements and methods of tests
GOST R 51686.1-2000: Connecting devices. Electrical copper conductors. Safety requirements for screw-type and screwless-type clamping units. Part 1. General requirements and particular requirements for clamping units for conductors from 0,2 up to 35 sq. mm (included)
GOST R IEC 227-3-94: Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
GOST R IEC 60227-3-2002: Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
GOST R IEC 61210-99: Connecting devices. Flat quick-connect terminations for electrical copper conductors. Safety requirements
GOST R IEC 998-2-4-96: Connecting devices for low-voltage circuits for household and similar purposes. Particular requirements for twist-on connecting devices
The Document is Referenced By:
GOST R 50345-2010: Electrical accessories. Circuit-breakers for overcurrent protection for household and similar installations. Part 2. Circuit-breakers for a.c. operation
GOST R 51686.1-2000: Connecting devices. Electrical copper conductors. Safety requirements for screw-type and screwless-type clamping units. Part 1. General requirements and particular requirements for clamping units for conductors from 0,2 up to 35 sq. mm (included)
|
Customers Who Viewed This Item Also Viewed:
 |
Controllers acting without
Language: English |
Building materials. Methods for combustibility test
Language: English |
Building materials spread flame test method
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Clear sheet glass. Specifications
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
