GOST R EN 1034-1-2012
ГОСТ Р ЕН 1034-1-2012
|
|
Paper-making and finishing machines. Safety requirements for the design and construction. Part 1. General requirements
Оборудование для изготовления и отделки бумаги. Требования безопасности для конструирования и изготовления. Часть 1. Общие требования
Status: Effective - Introduced for the first time. IUS 9-2013
The general requirements set forth in this standard apply to equipment for the manufacture and finishing of paper. This standard contains definitions and requirements applicable to all types of equipment for the manufacture and finishing of paper listed in Appendix A, and should be applied in conjunction with a special standard for the type of equipment. Special standards may contain additional requirements or deviations from EN 1034-1, in which case these requirements take precedence over the relevant provisions of EN 1034-1. The hazards addressed in this standard are listed in clause 4. This standard does not apply to paper processing equipment. See standards of the EN 1010 series. This standard does not apply to machines manufactured before the date of its introduction
Действие общих требований, установленных в настоящем стандарте, распространяется на оборудование для изготовления и отделки бумаги. Настоящий стандарт содержит определения и требования, применяемые ко всем видам оборудования для изготовления и отделки бумаги, перечисленным в приложении А, и должен применяться совместно со специальным стандартом для соответствующего вида оборудования. Специальные стандарты могут содержать дополнительные требования или отступления от EН 1034-1, в случае чего эти требования имеют преимущество перед соответствующими положениями EН 1034-1. Виды опасностей, рассматриваемые в настоящем стандарте, перечислены в разделе 4. Настоящий стандарт не применяют к оборудованию для переработки бумаги. См. стандарты серии ЕН 1010. Настоящий стандарт не применяют к машинам, изготовленным до даты введения его в действие
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
11/20/2012
SKU: RUSS71469
The Product is Contained in the Following Classifiers:
PromExpert »
SECTION III. LABOR PROTECTION AND SAFETY »
III Occupational safety requirements for production equipment and processes »
2 Safety requirements for certain types of work »
2.2 Operation of production machines and equipment »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.13 Testing and control of products of engineering industry »
4.13.2 Machines and equipment for special purposes »
4.13.2.4 Machines and equipment for mining, oil industry and quarrying »
ISO classifier »
37 TECHNOLOGY OF RECEPTION OF IMAGES »
37.100 Printing technology »
37.100.10 Equipment for reproduction »
National standards »
37 TECHNOLOGY OF RECEPTION OF IMAGES »
37.100 Printing technology »
37.100.10 Equipment for reproduction »
ISO classifier »
85 PULP AND PAPER INDUSTRY »
85.100 Equipment for paper production »
National standards »
85 PULP AND PAPER INDUSTRY »
85.100 Equipment for paper production »
National Standards for KGS (State Standards Classification) »
Latest edition »
T General technical and organizational and methodological standards »
T3 Physics and Mechanics »
T34 Oscillatory and wave-like movements. Bodies vibration. Sound. Acoustics »
The Document References:
GOST 14254-96: Degrees of protection provided by enclosures (IP Code)
GOST 30869-2003: Safety of machinery. Safety requirements for fluid power systems and their components. Pneumatics
GOST EN 1005-2-2005: Safety of machinery. Human physical performance. Part 2. Manual handling of machinery and component parts of machinery
GOST EN 1010-1-2011: Printing machinery. Safety requirements for the design and construction. Part 1. General requirements
GOST EN 1010-3-2011: Printing trades machinery. Safety requirements for the design and construction. Part 3. Cutting machines
GOST EN 1760-1-2004: Safety of machinery. Pressure sensitive protective devices. Part 1. General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
GOST EN 1837-2002: Safety of machinery. Integral lighting of machines
GOST R 51334-99: Safety of machinery. Safety distances to prevent danger zones being reached by the upper limbs
GOST R 51335-99: Safety of machinery. Minimum gaps to avoid crushing of parts of the human body
GOST R 51336-99: Safety of machinery. Emergency stop equipment. Functional aspects. Principles for design
GOST R 51337-99: Safety of machinery. Temperatures of touchable surfaces. Ergonomics data to establish temperature limit values for hot surfaces
GOST R 51338-99: Safety of machinery. Reduction of risk to health from hazardous substances emitted by machinery. Part 1. Principles and specifications for machinery manufacturers
GOST R 51339-99: Safety of machinery. Safety distances to prevent danger zones being reached by the lower limbs
GOST R 51341-99: Safety of machinery. Ergonomics requirements for the design of displays and control actuators. Part 2. Displays
GOST R 51342-99: Safety of machinery. Guards. General requirements for the design and construction of fixed and movable guards
GOST R 51343-99: Safety of machinery. Prevention of unexpected start-up
GOST R 52543-2006: Hydraulic drives. Safety requirements
GOST R 52743-2007: Pumps and pump units for pumping of liquids. General safety requirements
GOST R 53479-2009: Printing trades equipment. Methods for determination of noise emission dates. Accuracy grades 2 and 3
GOST R EN 1005-3-2010: Safety of machinery. Human physical performance. Part 3. Recommended force limits for machinery operation
GOST R EN 1010-2-2011: Printing trades machinery. Safety requirements for the design and construction. Part 2. Printing and varnishing machines including pre-press machinery
GOST R EN 1010-4-2011: Printing trades machinery. Safety requirements for the design and construction. Part 4. Bookbinding, paper-converting and finishing machines
GOST R EN 1010-5-2012: Printing machinery. Safety requirements for design and construction. Part 5. Machines for the production of corrugated board and machines for the conversion of flat and corrugated cardboard
GOST R EN 1127-1-2009: Explosive atmospheres. Explosion prevention and protection. Part 1. Basic concepts and methodology
GOST R EN 547-1-2008: Safety of machinery. Human body measurements. Part 1. Principles for determining the dimensions required for openings for whole body access into machinery
GOST R EN 547-2-2009: Safety of machinery. Human body measurement. Part 2. Principles for determining the opening dimensions required for access into machinery (machinery parts) by body parts
GOST R EN 547-3-2009: Safety of machinery. Human body measurement. Part 3. Anthropometric data
GOST R EN 614-1-2003: Safety of machinery. Ergonomic design principles. Part 1. Terms, definitions and general principles
GOST R IEC 60204-1-2007: Safety of machinery. Electrical equipment of machines and mechanisms. Part 1. General requirements
GOST R IEC 60825-1-2009: Safety of laser products. Part 1. Equipment classification, requirements and user's guide
GOST R ISO 12100-1-2007: Safety of machinery. Basic concepts, general principles for design. Part 1. Basic terminology, methodology
GOST R ISO 12100-2-2007: Safety of machinery. Basic concepts, general principles for design. Part 2. Technical principles
GOST R ISO 13849-1-2003: Safety of machinery. Safety-related parts of control systems. Part 1. General principles for design
GOST R ISO 14122-3-2009: Safety of machinery. Permanent means of access to machinery. Part 3. Stairs, stepladders and guard-rails.
GOST R ISO 14122-4-2009: Safety of machinery. Permanent means of access to machinery. Part 4. Vertical stairs
GOST R ISO 7731-2007: Ergonomics. Danger signals for public and work areas. Auditory danger signals
|
Customers Who Viewed This Item Also Viewed:
 |
Liquids for aircrafts systems. Method for determination thermo oxidizing stability and corrosion activity
Language: English |
Plastics structured-wall pipes and their fittings for sewerage systems outside the buildings. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
