GOST R ISO 4759-1-2009
ГОСТ Р ИСО 4759-1-2009
|
|
Tolerances for fasteners. Part 1: bolts, screws, studs and nuts. Product grades A, B and C
Изделия крепежные. Допуски. Часть 1. Болты, винты, шпильки и гайки. Классы точности А, В и С
Status: Not effective - Canceled. Registration information 735-st dated 06/29/2016 (official website of Rosstandart); IUS 1-2017
This standard establishes tolerances for bolts, screws, studs and nuts with ISO metric threads of accuracy classes A, B and C, as well as for self-cutting screws of accuracy class A. Note - The accuracy class of a product is determined by the size of tolerances, while class A is the most accurate, and class C is the least accurate. Tolerances, with the exception of threading tolerances, are selected from tolerances and landings using the ISO system specified in ISO 286-1 and ISO 286-2. Tolerances for metric threads are selected from a series of tolerance fields specified in ISO 965-3. Tolerances for self-tapping screws are given in ISO 1478. Tolerances for the shape and location of surfaces are established and specified in accordance with ISO 1101, ISO 8015 and ISO 2692. The tolerances specified in this standard apply to fasteners before coating them, unless specified otherwise. See also ISO 4042. Deviations from the tolerances specified in this standard are allowed in product standards, only in justified cases. If there is a discrepancy between the tolerance requirements of this standard and the product standard, preference is given to the product standard. It is recommended to use these tolerances also for non-standard fasteners. Dimensions and tolerances specified in this standard are in millimeters
Настоящий стандарт устанавливает допуски для болтов, винтов, шпилек и гаек с метрической резьбой ИСО классов точности А, В и С , а также ��ля самонарезающих винтов класса точности А. Примечание - Класс точности изделия определяется величиной допусков, при этом класс А является наиболее точным, а класс С - наименее точным. Допуски, за исключением допусков на резьбу, выбираются из допусков и посадок по системе ИСО, установленной в ИСО 286-1 и ИСО 286-2. Допуски на метрическую резьбу выбираются из серии полей допусков, установленных в ИСО 965-3. Допуски на резьбу самонарезающих винтов приведены в ИСО 1478. Допуски формы и расположения поверхностей устанавливаются и указываются в соответствии с ИСО 1101, ИСО 8015 и ИСО 2692. Допуски, установленные в настоящем стандарте, применяются к крепежным изделиям до нанесения на них покрытия, если не оговорено иное. См. также ИСО 4042. Отступления от допусков, установленных в настоящем стандарте, допускается в стандартах на изделия, только в обоснованных случаях. Если имеет место расхождение между требованиями к допускам настоящего стандарта и стандарта на изделие, предпочтение отдается стандарту на изделие. Рекомендуется использовать эти допуски также для нестандартных крепежных изделий. Размеры и допуски, установленные в настоящем стандарте, указаны в миллиметрах
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/10/2009
SKU: RUSS71991
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
21 Mechanical systems and general purpose devices »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
Standards for pipe fittings (TPA) »
13. Standards for basic components and parts of injection molding machines »
13.2 Fasteners »
ISO classifier »
21 MECHANICAL SYSTEMS AND GENERAL PURPOSE DEVICES »
21.060 Fasteners »
21.060.01 Fasteners in general »
National standards »
21 MECHANICAL SYSTEMS AND GENERAL PURPOSE DEVICES »
21.060 Fasteners »
21.060.01 Fasteners in general »
ISO classifier »
21 MECHANICAL SYSTEMS AND GENERAL PURPOSE DEVICES »
21.060 Fasteners »
21.060.10 Bolts, screws, studs »
National standards »
21 MECHANICAL SYSTEMS AND GENERAL PURPOSE DEVICES »
21.060 Fasteners »
21.060.10 Bolts, screws, studs »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G3 Fasteners for general engineering applications »
G30 Classification, nomenclature and general rules »
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 10753-86: Cross recesses for screws and wood screws. Dimensions and control methods
GOST 16093-2004: Basic norms of interchangeability. Metric screw thread. Tolerances. Clearance fits
GOST 24670-81: Bolts, screws and wood screws. Radius under the head
GOST 25346-89: Basic norms of interchangeability. Unified system of tolerances and fits. General, series of tolerances and fundamental deviations
GOST 25347-82: Basic norms of interchangeability. Unified system of tolerances and fits. Tolerance zones and recommendable fits
GOST 5915-70: Hexagon nuts, product grade B. Construction and dimensions
GOST 5927-70: Hexagon nuts (high precision). Construction and dimensions
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 53090-2008: Basic norms of interchangeability. Geometrical product specifications. Maximum material requirement, least material requirement and reciprocity requirement
GOST R 53442-2009: Basic norms of interchangeability. Geometrical product specifications. Tolerances of form, orientation, location and run-out
GOST R ISO 10664-2007: Star-type internal socket button for bolts and screws
GOST R ISO 1478-93: Tapping screws thread
GOST R ISO 4042-2009: Fasteners. Electroplated coatings
The Document is Referenced By:
GOST 11530-2014: Rail joint bolts. Specifications
GOST 16016-2014: Clamp bolts for rail track fastenings. Specifications
GOST 16017-2014: Inserted bolts for rail track fastenings. Specifications
GOST 21797-2014: Two-turn spring washers for railway track. Specifications
GOST 22032-76: Studs with threaded end of 1d. Product grade B. Construction and dimensions
GOST 24379.0-2012: Foundation bolts. General specifications
GOST 32484.3-2013: High-strength structural bolting assemblies for preloading. System HR - Hexagon bolt and nut assemblies
GOST 32484.4-2013: High-strength structural bolting assemblies for preloading. System HV - Hexagon bolt and nut assemblies
GOST 34519-2019: Industrial chimney and ventilation pipes. Rules for the organization and production of work, monitoring of performance and requirements for the results of work
GOST ISO 15071-2014: Hexagonal bolts with reduced head with flange. Precision class A
GOST ISO 23429-2014: Fasteners. Control of hexagon recesses with gauge
GOST ISO 4033-2014: Hex Nuts high (type 2). Precision classes A and B
GOST ISO 4034-2014: Hex Nuts, normal (type 1). Precision class C
GOST ISO 4035-2014: Nuts hexahedral, low, chamfered (type 0). Precision classes A and B
GOST ISO 4036-2014: Nuts, hexagonal, low without bevel (type 0). Accuracy class B
GOST ISO 4162-2014: Hexagonal bolts with reduced head with flange. Precision class A to class of precision B
GOST ISO 7040-2014: Nuts Hex normal self-stopped (with non-metallic insert), type 1. Strength class 5, 8 and 10
GOST ISO 7041-2014: Nuts Hex high self-stopped (with non-metallic insert), type 2. Strength class 9 and 12
GOST ISO 7043-2014: Nuts Hex high self-stopped with flange (with non-metallic insert), type 2. Precision classes A and B
GOST ISO 7380-1-2014: Round head screw. Part 1. Round head screw with hexagon socket
GOST ISO 7380-2-2014: Round head screw. Part 2. Round head screw with hexagon socket and rim
GOST ISO 7719-2014: Hex nuts, normal, self-stopping, all metal (Type 1). Strength class 5, 8 and 10
GOST ISO 7720-2014: Hex nuts, high, self-stopping, all metal (Type 2). Strength class 9
GOST ISO 8673-2014: Hexagon regular nuts (style 1) with fine pitch thread. Product grades A and B
GOST ISO 8674-2014: Nuts hexahedral high (type 2) with a fine-pitch thread. Precision classes A and B
GOST ISO 8675-2014: Nuts hexahedral low chamfered (type 0) with fine pitch thread. Precision classes A and B
GOST R 52643-2006: High-strength screws and nuts washers for metal structures. General specifications
GOST R 52644-2006: Hexagon bolts for high-strength structural bolting with large width across flats. Specifications.
GOST R 52645-2006: Hexagon nuts for high-strength structural bolting with large width across flats. Specifications.
GOST R 53664-2009: High-strength cheese-head and conical bolts for bridge building. Nuts and washers for them. Specifications
GOST R 53682-2009: Fired heaters for refineries. General technical requirements
GOST R 53819-2010: Vehicles. Fastenings wheels. Technical requirements and test methods
GOST R 54482-2011: Piping connections for general-use hydraulic fluid power. Hose fittings with metric stud ends and O-ring. Technical requirements
GOST R 54786-2011: Fastening parts for detachable connections of nuclear power plants. Specifications.
GOST R 55738-2013: Studs and ceramic ferrules for stud welding
GOST R 55739-2013: Hexagon bolts with flange
GOST R 55742-2013: Screws with cylindrical head and large star-type internal socket
GOST R 57979-2017: Screwdrivers for fi tting and assembling. Blades of screwdrivers of slotted screws and woodscrews. Dimensions
GOST R ISO 10509-2013: Hexagon flange head tapping screws
GOST R ISO 10642-2012: Hexagon socket countersunk head screws
GOST R ISO 1207-2013: Slotted cheese head screws. Product grade A
GOST R ISO 12474-2012: Hexagon socket head cap screws with metric fine pitch thread
GOST R ISO 14580-2012: Hexalobular socket cheese head screws
GOST R ISO 14584-2012: Star type socket raised countersunk head screws
GOST R ISO 14585-2012: Hexalobular socket pan head tapping screws
GOST R ISO 14586-2012: Hexalobular socket countersunk head tapping screws
GOST R ISO 14587-2012: Hexalobular socket raised countersunk head tapping screws
GOST R ISO 1479-2013: Hexagon head tapping screws
GOST R ISO 1481-2013: Slotted pan head tapping screws
GOST R ISO 1482-2013: Slotted countersunk head tapping screws
GOST R ISO 1483-2013: Slotted raised countersunk head tapping screws
GOST R ISO 15072-2013: Hexagon flange reduced head bolts with fine pitch thread. Product grade A
GOST R ISO 1580-2013: Slotted pan head screws. Product grade A
GOST R ISO 2009-2013: Slotted raised countersunk head screws. Product grade A
GOST R ISO 2010-2013: Slotted raised countersunk head screws. Product grade A
GOST R ISO 3269-2009: Fasteners. Acceptance inspection
GOST R ISO 4014-2013: Hexagon head bolts. Product grades A and B
GOST R ISO 4016-2013: Hexagon head bolts. Product grade C
GOST R ISO 4017-2013: Hexagon head screws. Product grades A and B
GOST R ISO 4018-2013: Hexagon head screws. Product grade C
GOST R ISO 4026-2013: Hexagon socket set screws with flat point
GOST R ISO 4027-2013: Hexagon socket set screws with cone point
GOST R ISO 4028-2013: Hexagon socket set screws with dog point
GOST R ISO 4029-2013: Hexagon socket set screws with cup point
GOST R ISO 4161-2013: Hexagon nuts with flange, style 2. Coarse thread
GOST R ISO 4762-2012: Hexagon socket head screws
GOST R ISO 4766-2013: Slotted set screws with flat point
GOST R ISO 7042-2011: Prevailing torque type all-metal hexagon nuts, style 2. Property classes 5, 8, 10 and 12
GOST R ISO 7045-2013: Pan head screws with type H or type Z cross recess. Product grade A
GOST R ISO 7046-1-2013: Countersunk flat head screws (common head style) with type H or type Z cross recess. Product grade A. Part 1. Steel screws of property class 4.8
GOST R ISO 7046-2-2013: Countersunk flat head screws (common head style) with type H or type Z cross recess. Product grade A. Part 2. Steel screws of property class 8.8, stainless steel screws and non-ferrous metal screws
GOST R ISO 7047-2013: Raised countersunk head screws with type H or type Z cross recess. Product grade A
GOST R ISO 7048-2013: Cross-recessed cheese head screws
GOST R ISO 7049-2012: Cross-recessed pan head tapping screws
GOST R ISO 7050-2012: Cross-recessed countersunk (flat) head tapping screws
GOST R ISO 8676-2013: Hexagon head screws with metric fine pitch thread. Product grades A and B
GOST R ISO 8765-2013: Hexagon head bolts with metric fine pitch thread. Product grades A and B
GOST R ISO 8992-2011: Fasteners. General requirements for bolts, screws, studs and nuts
SP 83.13330.2016: Industrial furnaces and brick chimneys
ST TsKBA 037-2006: Pipe fittings. Packing glands. Construction, main dimensions and technical requirements
|
Customers Who Viewed This Item Also Viewed:
 |
Liquid lubricating and plastic materials. Method of test for lubricating properties on four ball machine
Language: English |
Armour clothes. Classification and general technical requirements
Language: English |
Food products. Methods for detection and quantity determination of coliformes
Language: English |
Natural gas. Methods of calculation of physical properties. Calculation of physical properties on base information on density of standards conditions and nitrogen and carbon dioxide contents
Language: English |
Hotels design
Language: English |
Railroad rails. General specifications
Language: English |
Potassium chloride
Language: English |
Controllers acting without
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
