imgalt

GOST 31384-2008

ГОСТ 31384-2008

Structural concrete protection against corrosion. General requirements

Защита бетонных и железобетонных конструкций от коррозии. Общие технические требования

Status: Not effective - Superseded. Registration information 1361-st dated 10/05/2017 (official website of Rosstandart); IUS 2-2018

The standard establishes the requirements taken into account in the design of corrosion protection of concrete and reinforced concrete structures in buildings and structures intended for use in aggressive environments with temperatures from minus 70 degrees. C to plus 50 degrees. C. The standard defines technical requirements for the protection against corrosion of concrete and reinforced concrete structures for a service life of 50 years. For long service life of structures, protection against corrosion should be carried out according to special requirements. Designing the reconstruction of buildings and structures should provide an analysis of the corrosion state of structures and protective coatings, taking into account the type and degree of aggressiveness in the new operating conditions. The requirements of the standard do not apply to the design of protection of concrete and reinforced concrete structures from corrosion caused by radioactive substances, as well as the design of structures made of special concrete (polymer concrete, acidic, heat-resistant concrete, etc.).

Стандарт устанавливает требования, учитываемые при проектировании защиты от коррозии бетонных и железобетонных конструкций в зданиях и сооружениях, предназначенных для эксплуатации в агрессивных средах с температурой от минус 70 град. С до плюс 50 град. С. В стандарте определены технические требования к защите от коррозии бетонных и железобетонных конструкций для срока эксплуатации 50 лет. При больших сроках эксплуатации конструкций защита от коррозии должна выполняться по специальным требованиям. Проектирование реконструкции зданий и сооружений должно предусматривать анализ коррозионного состояния конструкций и защитных покрытий с учетом вида и степени агрессивности в новых условиях эксплуатации. Требования стандарта не распространяются на проектирование защиты бетонных и железобетонных конструкций от коррозии, вызываемой радиоактивными веществами, а также на проектирование конструкций из специальных бетонов (полимербетонов, кислото-, жаростойких бетонов и т.п.).

Choose Language: 
Format: Electronic (pdf/doc)

Approved: Federal Agency for Technical Regulation and Metrology, 10/26/2009

SKU: RUSS72625

Price: $808.00



imgalt

The Product is Contained in the Following Classifiers:

Construction (Max) » Regulations » Documents System of normative documents in construction » 5. Regulatory documents for building structures and products » k.52 Reinforced concrete and concrete structures »

ISO classifier » 91 CONSTRUCTION MATERIALS AND CONSTRUCTION » 91.120 Protection of buildings, inside and out » 91.120.99 Protection of buildings, inside and out, other aspects »

National standards » 91 CONSTRUCTION MATERIALS AND CONSTRUCTION » 91.120 Protection of buildings, inside and out » 91.120.99 Protection of buildings, inside and out, other aspects »

National Standards for KGS (State Standards Classification) » Latest edition » Zh Construction and building materials » Zh3 Building structures and parts » Zh39 Test methods. Packaging. Marking »


The Document is Replaced With:

GOST 31384-2017: Protection of concrete and reinforced concrete structures against corrosion. General technical requirements

As a Replacement Of:

ST SEV 4420-83: Corrosion protection in construction. Concrete and reinforced concrete constructions. General provisions

The Document References:

GOST 1.0-92: State System for Standardization of Russian Federation. Basic principles

GOST 10060.0-95: Methods for the determination of frost-resistance. General requirements

GOST 10060.1-95: Concretes, Basic Method For The Determination Of Frost-Resistance

GOST 10060.2-95: Concretes, rapid method for the determination of frost-resistance by repeated alternated freezing and thawing

GOST 10178-85: Portland cement and portland blastfurnace slag cement. Specifications

GOST 10834-76: Hydrophobizing liquid 136-41. Specifications

GOST 10884-94: Thermomechanically hardened steel bars for reinforced concrete constructions. Specifications

GOST 12.3.002-75: Occupational safety standards system. Manufacturing processes. General safety requirements

GOST 12.3.005-75: Painting works

GOST 21.513-83: System of building documents. Anticorrosive protection of building structures. Working drawings

GOST 22266-94: Sulphate-resistant cements. Specifications

GOST 23494-79: Primer XC-059, enamels XC-759, varnish XC-724. Specifications

GOST 23732-79: Water for concretes and mortars. Specifications

GOST 24211-2003: Additives for concretes and mortars. General specifications

GOST 25485-89: Cellular concretes. Specifications

GOST 26633-91: Heavy-weight and sand concretes. Specifications

GOST 27751-88: Reliability of the constructions and the foundations. Principal rules of the calculations

GOST 30333-2007: Chemical production safety passport. General requirements

GOST 30515-97: Cements General specifications

GOST 31108-2003: General structural Portland clinker cements. Specifications

GOST 6465-76: Enamels PF-115. Specifications

GOST 6631-74: Enamels НЦ-132. Specifications

GOST 7313-75: Enamels ХВ-785 and lacquer XB-784. Specifications

GOST 8267-93: Crushed stone and gravel of solid rocks for construction works. Specifications

GOST 8736-93: Sand for construction works. Specifications

GOST 9.602-2005: Unified system of corrosion and ageing protection. Underground constructions. General requirements for corrosion protection

GOST 926-82: Enamels ПФ-133. Specifications

GOST 969-91: Alumina and high alumina cements. Specifications

GOST 9757-90: Artificial porous gravel, crushed stone and sand artificially produced expanded/foamed gravel, crushed rock and sand]. Specifications

GOST R 52544-2006: Weldable deformed reinforcing rolled products of A500C and B500C classes for reinforcement of concrete constructions. Specifications

GOST R 52804-2007: Protection against corrosion of concrete and reinforced concrete constructions. Test methods

SNiP 10-01-94: System of normative documents in construction. Basic provisions.

SNiP 12-03-2001: Labor safety in construction industry

SNiP 12-04-2002: Safety in construction. Part 2. Construction works

SNiP 2.03.11-85: Corrosion protection of buildings structures

SNiP 23-02-2003: Buildings Heat Insulation

SNiP 52-01-2003: Concrete and ferroconcrete structures. Principal rules

SP 52-101-2003: Concrete and reinforced concrete structures without prestressing

SP 52-102-2004: Pre-stressed concrete structures

ST SEV 4419-83: Corrosion protection in construction. Building structures. Terms and Definitions

The Document is Referenced By:

GOST 18128-2018: Timber framed asbestos cement exterior wall panels supplied with insulation. Specifications

GOST 20054-2016: Concrete non-pressure pipes. Specifications

GOST 25192-2012: Concretes. Classification and general technical requirements

GOST 25818-2017: Fly ash thermal power plants for concrete. Technical conditions

GOST 25820-2014: Lightweight aggregates concretes. Specifications

GOST 25912-2015: Prestressed reinforced concrete slabs for aerodrome pavement. Specifications

GOST 26633-2012: Heavy-weight and sand concretes. Specifications

GOST 26633-2015: Heavy-weight and sand concretes. Specifications

GOST 32016-2012: Products and systems for the protection and repair of concrete structures. General requirements

GOST 32017-2012: Products and systems for the protection and repair of concrete structures. Requirements for systems for concrete protection in the course of repair works

GOST 32871-2014: Automobile roads of general use. Pipes for road culvert. Technical requirements

GOST 6482-2011: Ferroconcrete nonpressure pipes. Technical specifications.

GOST 7473-2010: Fresh concrete. Specifications

GOST 8020-2016: Concrete and reinforced concrete structures for man-holes of sewerage, water supply and gas supply pipeline systems. Specification

GOST R 56178-2014: Modifiers of organic-mineral origin of MB type for concretes, mortars and dry mixes. Specifications

GOST R 56600-2015: Reinforced concrete prestressed slabs for pavements of roads. Specifications

GOST R 56703-2015: Dry building in-depth waterproofing capillary mixes based on cement binder. Specifications

GOST R 57190-2016: Grounding conductors and grounding devices different purposes. Terms and definitions

GOST R 57255-2016: Photo catalytic self-cleaning concrete. Specifications

MDS 12-65.2014: Project production work. Concreting of reinforced concrete structures of a building (structure) using concrete pumps

ODM 218.2.066-2016: Guidelines for the use of anchor piles and micropiles as part of the engineering protection of roads

ODM 218.2.087-2017: Recommendations for the design and construction of culverts of spiral-wavy metal corrugated pipes

ODM 218.3.001-2010: Recommendations for the diagnosis of active corrosion of reinforcement in reinforced concrete structures of bridges on highways using the half-cell potential method

ODM 218.3.036-2013: Recommendations for the technology of rehabilitation of cracks and seams in existing road surfaces

ODM 218.3.070-2016: Guidelines on formulation of self-compacting concrete with prescribed waterproof properties for bored piles

ODM 218.3.095-2017: Corrosion protection of concrete and reinforced concrete structures of transport facilities

ODM 218.6.030-2017: Recommendations for establishing and warranty periods and service life of structural elements of bridge structures

PNST 105-2016: Sulfur concrete mixtures and sulfur concrete. General specifications

R-NP SRO SSK 02-2015: Recommendations for concrete works in winter period

SP 120.13330.2012: Subway systems

SP 229.1325800.2014: Reinforced concrete structures of underground and utility systems. Protection against corrosion

SP 250.1325800.2016: Building and structures. Protection against groundwater

SP 28.13330.2012: Corrosion protection of buildings structures. Updated living edition of SNiP 2.03.11-85

SP 287.1325800.2016: Marine berthing facilities. Rules of design and construction

SP 289.1325800.2017: Constructions cattle-breeding, poultry-breeding and beast-breeding. Design rules

SP 340.1325800.2017: Reinforced concrete and concrete structures of cooling towers. Design rules

SP 343.1325800.2017: Constructions of the industrial enterprises. The rules of operation

SP 43.13330.2012: Structures for industrial installations

SP 469.1325800.2019: The construction of livestock, poultry and animal husbandry enterprises. Terms of Use

SP 70.13330.2012: Bearing and enclosing structures. Updated living edition of SNiP 3.03.01-87

SP 72.13330.2016: Protection of buildings, facilities and structures against corrosion

SP 81.13330.2017: The reclamation systems and construction

SP 95.13330.2016: Concrete and reinforced concrete structures made of dense calcium-silicate concrete

SP 96.13330.2016: Ferrocement structures

STO DOKTOR BETON 68686983-001-2011: Dry building mixtures trade mark "ДОКТОР БЕТОН®" for waterproofing and repair concrete construction. Classification. Nomenclature of indicators. Technical requirements

STO DOKTOR BETON 68686983-002-2011: Dry building mixtures trade mark "ДОКТОР БЕТОН®" for waterproofing and repair concrete construction. Technical specifications and quality characteristics

Customers Who Viewed This Item Also Viewed:

imgalt imgalt
Building materials. Methods for combustibility test
Language: English
Price: $162.00
imgalt
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English
Price: $745.00
imgalt
Building materials spread flame test method
Language: English
Price: $147.00
imgalt
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English
Price: $349.00
imgalt
Steel welded vessels and apparatus. General technical conditions
Language: English
Price: $549.00
imgalt
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English
Price: $414.00
imgalt
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English
Price: $700.00
imgalt

YOUR ORDERING MADE EASY!

RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.

Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.

We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.

Placing Your Order

Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).

Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.

For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.

For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.

Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.

Your Order Best Quality and Authenticity Guarantee

Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).

We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.

We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.

All Codes and Regulations

All Categories

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!