GOST R 54560-2011
ГОСТ Р 54560-2011
|
|
Fiberglass reinforced thermosetting plastic pipes and parts of pipelines. Specifications
Трубы и детали трубопроводов из реактопластов, армированных стекловолокном. Технические условия
Status: Not effective - Superseded. Registration information 2073-st dated 11/27/2015 (Rosstandart official website); IUS 6-2016
This standard applies to pipes and pipeline parts made from thermosetting plastics based on unsaturated polyester and vinyl ester resins reinforced with fiberglass (hereinafter referred to as pipes and fittings) with a nominal diameter of DN from 300 to 3000, intended for use in pressure and non-pressure pipeline water supply and sewage systems. Pipes and fittings are intended for transportation of the following working media: - domestic, industrial and storm sewage; - aqueous solutions of chemical elements and compounds; - technical water; - drinking water and liquid foods. The allowable working pressure is up to 3.2 MPa, the admissible rigidity of pipes is up to 10,000 Pa, the allowable constant temperature of the working medium is up to plus 35 (deg.) C at an operating pressure not exceeding the allowable one. The standard does not apply to pipes and fittings intended for internal water supply and drainage systems, as well as pipes and fittings manufactured by the methods: - continuous winding with winding angles of fiberglass yarns and tapes less than 90 (degrees); - periodic winding; - centrifugal molding
Настоящий стандарт распространяется на трубы и детали трубопроводов из реактопластов на основе ненасыщенных полиэфирных и винилэфирных смол, армированных стекловолокном (далее трубы и фитинги), номинальным диаметром DN от 300 до 3000, предназначенные для использования в напорных и безнапорных трубопроводных системах водоснабжения и водоотведения. Трубы и фитинги предназначены для транспортирования следующих рабочих сред: - бытовых, промышленных и ливневых стоков; - водных растворов химических элементов и соединений; - технической воды; - питьевой воды и жидких пищевых продуктов. Допустимое рабочее давление до 3.2 МПа, допустимая жесткость труб до 10000 Па, допустимая постоянная температура рабочей среды - до плюс 35 (град.) С при рабочем давлении, не превышающем допустимое. Стандарт не распространяется на трубы и фитинги, предназначенные для систем внутреннего водоснабжения и водоотведения, а также на трубы и фитинги, изготовляемые методами: - непрерывной намотки с углами намотки стекловолоконных нитей и лент менее 90 (град.); - периодической намотки; - центробежного формования
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
11/29/2011
SKU: RUSS72647
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
23 Hydraulic and pneumatic systems and components for general use. »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
032/2013 TR CU. On safety of overpressure equipment »
Regulations and standards (to 032/2013 TR CU) »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.10 Testing and monitoring products of rubber and plastics industry »
4.10.2 Plastic Products »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.20 Plastic pipes »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.20 Plastic pipes »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.45 Plastic fittings »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.45 Plastic fittings »
The Document is Replaced With:
GOST R 54560-2015: Fibre reinforced thermosetting plastic pipes and parts of pipelines. Specifications
The Document References:
Federal Law 184-FZ: About technical regulation
GN 2.2.5.1313-03: Maximum allowable concentrations (MACs) of harmful substances in occupational air
GN 2.3.3.972-00: Nutrition hygiene. Package, crockery, equipment and other types of productions, contacting with food. Maximum admissible amounts (MAA) of chemical substances, emitting from materials contacting with food
GOST 11012-69: Plastics. Method of test for resistance to abrasion
GOST 11358-89: Dial-type thickness gauges and dial-type wall thickness gauges graduated in 0,01 and 0,1 mm. Specifications
GOST 12.1.004-91: Fire safety. General requirements
GOST 12.1.005-88: General sanitary requirements for working zone air
GOST 12.1.018-93: Fire and explosion safety of static electricity. General requirements.
GOST 12.1.044-89: Fire and explosion hazard of substances and materials. Nomenclature of indices and methods of their determination
GOST 12.2.003-91: Industrial equipment. General safety requirements
GOST 12.3.030-83: Occupation safety standards system. Safety requirements. Plastics processing
GOST 12.4.004-74: Filtering protective mask RPG-67
GOST 12.4.011-89: Occupational safety standards system. Means of protection. General requirements and classification
GOST 12.4.021-75: Ventilation systems. General requirements
GOST 12.4.028-76: Respirators шб-1 "lepestok"
GOST 12.4.068-79: Occupational safety standards system. Dermatologic personal safety means. Classification and general requirements
GOST 12.4.121-83: Industrial filtering gas-masks
GOST 12815-80: Flanges for valves, fittings and pipelines for Pnom from 0,1 to 20 MPa (from 1 to 200 kgf/sq sm). Types. Connecting dimensions and dimensions of sealing surfaces
GOST 13344-79: Waterproof abrasive cloth. Specifications
GOST 15139-69: Plastics. Methods for the determination of density (mass density)
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15173-70: Plastics. Method for determination of mean coefficient of linear thermal expansion
GOST 17.1.3.13-86: Hydrosphere. General requirements for surface water protection against pollution
GOST 17.2.3.01-86: Nature protection. Atmosphere. Air quality control regulations for populated areas
GOST 17.2.3.02-78: Regulations for establishing permissible emissions of noxious pollutants from industrial enterprises
GOST 17.4.3.04-85: Nature protection. Soils. General requirements for contamination control and protection
GOST 17139-2000: Textile glass. Roving. Specifications
GOST 19300-86: Instruments for measurement of surface roughness by the profile method. Contact profilographs and profilometers. Types and main parameters
GOST 20010-93: Industrial rubber gloves
GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements
GOST 22235-2010: Freight cars for 1520 mm gauge main line railways. General requirements for safety in loading-unloading and shunting operations
GOST 24157-80: Plastic pipes. Method of determination of the resistance to constant internal pressure
GOST 25.601-80: Design calculation and strength testing. Methods of mechanical testing of polymeric composite materials. Test for tensile properties on plane specimens at normal, elevated and law temperatures
GOST 25.603-82: Design calculation and strength testing. Methods of mechanical testing of polymeric composite materials. Test for tensile properties of ring specimens at normal, elevated and low temperatures
GOST 25.604-82: Design calculation and strength testing. Methods of mechanical testing of polymeric composite materials. Test for bending properties at normal, elevated and low temperatures
GOST 25336-82: Laboratory glassware and equipment. Basic parameters and dimensions
GOST 2603-79: Reagents. Acetone. Specifications
GOST 263-75: Rubber. Method for the determination of Shore A hardness
GOST 270-75: Rubber. Method of the determination elastic and tensile stress-strain properties
GOST 27078-86: Thermoplastic pipes. Methods of determination of the tubes length after heating
GOST 3749-77: Checking 90° squares. Specifications
GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications
GOST 4650-80: Plastics. Methods for the determination of water absorption
GOST 5378-88: Vernier protractors. Specifications
GOST 7470-92: Micrometric depth meters. Specifications
GOST 7502-98: Measuring metal tapes. Specifications
GOST 9.024-74: Unified system of corrosion and ageing protection. Rubbers. Methods of heat ageing stability determination
GOST 9.029-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing of resistance to ageing under static deformation of compression
GOST 9.030-74: Unified system of corrosion and ageing protection. Vulcanized rubbers. Method of testing resistance to attack by corrosive media in limp state
GOST 9078-84: Flat pallets
GOST 9147-80: Laboratory porcelain ware and apparatus. Specifications
GOST 9378-93: Roughness comparison specimens
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 12.1.019-2009: Occupational safety standards system. Electrical safety. General requirements and nomenclature of kinds of protection
GOST R 52108-2003: Resources saving. Waste treatment. Basic principles
GOST R 54559-2011: Fibre reinforced thermosetting plastic pipes and parts of pipelines. Terms and definitions
GOST R ISO 3126-2007: Plastics piping systems. Plastics components of piping systems. Determination of dimensions
SanPiN 2.1.7.1322-03: Hygienic requirements regarding dumping and decontamination of industrial and consumable waste
SNiP 2.04.03-85: Sewage. External systems and structures
SNiP 3.05.05-84: Processing equipment and process pipelines
SP 40-102-2000: Design and installation of pipeline systems of water supply and sewerage made of polymeric materials. General requirements. To replace SN 478-80
SP 40-104-2001: Design and installation of underground pipelines of water supply with fibreglass pipes. Amendments, published in the BST 2002, №1 № 4, № 5, 2005.
SP 40-105-2001: Design and installation of underground sewage pipelines made of fibreglass pipes
The Document is Referenced By:
ODM 218.3.046-2015: Recommendations about technology of repair of water throughput pipes with use of composite materials
RMD 40-20-2013 Sankt-Peterburg: Designing and installation pipelines for water supply and sewage systems in Saint-Petersburg
RMD 40-20-2016 Sankt-Peterburg: Installation of water supply and drainage networks in St. Petersburg
|
Customers Who Viewed This Item Also Viewed:
 |
Unified system for design documentation. Types and sets of design documentation
Language: English |
Loads and impacts
Language: English |
Vessels and Apparatus. Norms and methods of strength calculation from wind loads, seismic influence and other external loads
Language: English |
Articulated connector devices with cast male and female parts for freight cars of articulated type. General technical specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
