GOST R 54431-2011
ГОСТ Р 54431-2011
|
|
Metal-working machines. General safety requirements
Станки металлообрабатывающие. Общие требования безопасности
Status: Effective - Introduced for the first time. IUS 6-2012
This standard establishes general safety requirements and applies to metalworking machines of all types coming into operation, including those that are part of automatic lines and robotic systems, as well as devices used together with them, designed for connection to an AC mains voltage of up to 1000 V between phases and frequency up to 200 Hz and direct current up to 1500 V, designed for operation in climatic conditions UHL4 according to GOST 15150. Special safety requirements depend characteristics of the design of the machine or its operating conditions should be indicated in the technical documentation for specific types of machines
Настоящий стандарт устанавливает общие требования безопасности и распространяется на поступающие в эксплуатацию металлообрабатывающие станки всех видов, в том числе входящие в состав автоматических линий и роботизированных комплексов, а также на применяемые совместно с ними устройства, рассчитанные на подключение к питающей сети переменного тока напряжением до 1000 В между фазами и частотой до 200 Гц и постоянного тока до 1500 В, предназначенные для работы в климатических условиях УХЛ4 по ГОСТ 15150. Специальные требования безопасности в зависимости от особенностей конструкции станка или условий его эксплуатации следует указывать в технической документации на конкретные виды станков
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
9/28/2011
SKU: RUSS72869
The Product is Contained in the Following Classifiers:
PromExpert »
SECTION III. LABOR PROTECTION AND SAFETY »
III Occupational safety requirements for production equipment and processes »
2 Safety requirements for certain types of work »
2.2 Operation of production machines and equipment »
ISO classifier »
13 ENVIRONMENTAL PROTECTION, HUMAN PROTECTION AGAINST ENVIRONMENTAL IMPACT. SECURITY »
13.110 Safety of machinery »
National standards »
13 ENVIRONMENTAL PROTECTION, HUMAN PROTECTION AGAINST ENVIRONMENTAL IMPACT. SECURITY »
13.110 Safety of machinery »
ISO classifier »
25 MECHANICAL ENGINEERING »
25.080 Metal cutting machines »
National standards »
25 MECHANICAL ENGINEERING »
25.080 Metal cutting machines »
ISO classifier »
25 MECHANICAL ENGINEERING »
25.080 Metal cutting machines »
25.080.01 Machine tools in general »
National standards »
25 MECHANICAL ENGINEERING »
25.080 Metal cutting machines »
25.080.01 Machine tools in general »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G0 General rules and regulations for engineering »
G07 Safety »
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 12.0.002-80: Occupational safety standards system. Terms and definitions
GOST 12.1.001-89: Occupational safety standards system. Ultrasound. General safety requirements
GOST 12.1.003-83: Noise. General safety requirements
GOST 12.1.005-88: General sanitary requirements for working zone air
GOST 12.1.012-2004: Occupational safety stаndards system. Vibration safety. General requirements
GOST 12.2.003-91: Industrial equipment. General safety requirements
GOST 12.2.007.10-87: Occupational safety standards system. Installations, generators and induction heaters for electrothermics, ultrasonic installations and generators. Safety requirements
GOST 12.2.062-81: Occupational safety standards system. Industrial equipment. Safety protectors
GOST 12.2.064-81: Occupational safety standards system. Controls of industrial equipment. General safety requirements
GOST 12.2.107-85: Occupational safety standards system. Noise. Metal-cutting machine tools. Allowable noise characteristics
GOST 12.4.040-78: Industrial equipment controls
GOST 14254-96: Degrees of protection provided by enclosures (IP Code)
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 17677-82: Light fixtures
GOST 18322-78: Equipment maintenance and repair system. Terms and definitions
GOST 21752-76: Man-machine system Control hand wheels and steering wheels General ergonomic requirements
GOST 21753-76: Man -machine system control levers
GOST 22269-76: Man-machine system Operator workplace layout of workplace elements General ergonomic requirements
GOST 22613-77: Man-machine system. Rotary switches and commutators. General ergonomic requirements
GOST 22614-77: «Man-machine» system. Key-actuated and push-button switches and commutators. General ergonomic requirements
GOST 24940-96: Buildings and structures. Methods of measuring luminance
GOST 25557-2006: Machine tools tapers. Basic dimensions
GOST 26642-85: Numerical control units for metalworking machines. External communication with machines
GOST 28288-89: Light fixtures with built-in
GOST 30457-97: Acoustics. Determination of sound power levels of noise sources using sound intensity. Measurement at discrete points. Engineering method
GOST 30683-2000: Noise of machines. Measurement of emission sound pressure levels at a work station and at other specified positions. Method requiring environmental corrections
GOST 30691-2001: Noise of machines. Declaration and verification of noise emission values
GOST 30720-2001: Noise of machines. Determination of emission sound pressure levels at a work station and at other specified positions from the sound power level
GOST 30869-2003: Safety of machinery. Safety requirements for fluid power systems and their components. Pneumatics
GOST 31177-2003: Safety of machinery. Safety requirements for fluid power systems and their components. Hydraulics
GOST 6697-83: Power supply systems, sources, converters and receivers of electric alternating current energy rated frequencies from 0,1 to 10000 Hz and tolerances
GOST 7110-82: Hand lamps
GOST 8607-82: Light fixtures for illumination of domestic and public interiors
GOST 9146-79: Machines. Controls. Direction of action
GOST 9411-91: Colored optical glass
GOST EN 1005-2-2005: Safety of machinery. Human physical performance. Part 2. Manual handling of machinery and component parts of machinery
GOST EN 1070-2003: Safety of machinery. Terms and definitions
GOST EN 12415-2006: Safety of metal-working machine tools. Numerically controlled turning machines and turning centres
GOST EN 12417-2006: Safety of metal-working machine tools. Machining centres
GOST EN 12478-2006: Safety of machine tools. Large numerically controlled turning machines and large turning centres
GOST EN 12626-2006: Safety of metal-working machine tools. Laser processing machines
GOST EN 13128-2006: Safety of metal-working machine tools. Milling machines (including boring machines)
GOST EN 1760-1-2004: Safety of machinery. Pressure sensitive protective devices. Part 1. General principles for the design and testing of pressure sensitive mats and pressure sensitive floors
GOST EN 1837-2002: Safety of machinery. Integral lighting of machines
GOST ISO 13851-2006: Safety of machinery. Two-hand control devices. Functional aspects and design principles
GOST ISO 13855-2006: Safety of machinery. Positioning of protective equipment with respect to the approach speeds of parts of the human body
GOST ISO 8995-2002: Principles of visual ergonomics. The lighting of indoor work systems
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 12.4.026-2001: Occupational safety standards system. Safety colors, safety signs and signal marking. Purpose and rules of application. General technical requirements and characteristics. Test methods
GOST R 51101-97: Metalworking and woodworking machines small-size. Testing methods safety requirements
GOST R 51317.6.2-2007: Electromagnetic compatibility of technical equipment. Immunity of technical equipment intended for use in industrial environments. Requirements and test methods
GOST R 51317.6.3-99: Electromagnetic compatibility of technical equipment. Emission from technical equipment intended for use in residential, commercial and light-industry environments. Limits and test methods
GOST R 51317.6.4-99: Electromagnetic compatibility of technical equipment. Emission from technical equipment intended for use in industry environments. Limits and test methods
GOST R 51321.1-2007: Low-voltage switchgear and control gear assemblies. Part 1. Type-tested and partially type-tested assemblies. General technical requirements and test methods
GOST R 51334-99: Safety of machinery. Safety distances to prevent danger zones being reached by the upper limbs
GOST R 51335-99: Safety of machinery. Minimum gaps to avoid crushing of parts of the human body
GOST R 51336-99: Safety of machinery. Emergency stop equipment. Functional aspects. Principles for design
GOST R 51337-99: Safety of machinery. Temperatures of touchable surfaces. Ergonomics data to establish temperature limit values for hot surfaces
GOST R 51338-99: Safety of machinery. Reduction of risk to health from hazardous substances emitted by machinery. Part 1. Principles and specifications for machinery manufacturers
GOST R 51339-99: Safety of machinery. Safety distances to prevent danger zones being reached by the lower limbs
GOST R 51340-99: Safety of machinery. Basic characteristic of visual and auditory danger signals. Technical requirements and methods for testing
GOST R 51341-99: Safety of machinery. Ergonomics requirements for the design of displays and control actuators. Part 2. Displays
GOST R 51342-99: Safety of machinery. Guards. General requirements for the design and construction of fixed and movable guards
GOST R 51343-99: Safety of machinery. Prevention of unexpected start-up
GOST R 51344-99: Safety of machinery. Principles for risk assessment
GOST R 51345-99: Safety of machinery. Interlocking devices associated with guards. Principles for design and selection
GOST R 51401-99: Noise of machines. Determination of sound power levels of noise sources using sound pressure. Engineering method in an essentially free field over a reflecting plane
GOST R 51402-99: Noise of machine. Determination of power levels of noise sources using sound pressure. Survey method using an enveloping measurement surface over a reflecting plane
GOST R 51838-2001: Safety of machinery. Electrical equipment for industrial machines. Test methods
GOST R 54350-2011: Lighting fittings. Light requirements and test methods
GOST R EN 1005-1-2008: Safety of machinery. Human physical performance. Part 1. Terms and definitions
GOST R EN 12717-2006: Safety of machine tools. Drilling machines
GOST R EN 12840-2006: Safety of machine-tools. Manually controlled turning machines with or without automatic control
GOST R EN 12957-2007: Safety of metal-working machine tools. Electrodisharge machines
GOST R EN 13218-2006: Safety of machine-tools. Stationary grinding machines
GOST R EN 13788-2007: Safety of metal-working machine tools. Multi-spindle automatic turning machines
GOST R EN 13898-2009: Machine tools. Safety. Sawing machines for metal cold cutting
GOST R EN 414-2002: Safety of machinery. Rules for the drafting and presentation of safety standards
GOST R EN 547-1-2008: Safety of machinery. Human body measurements. Part 1. Principles for determining the dimensions required for openings for whole body access into machinery
GOST R EN 547-2-2009: Safety of machinery. Human body measurement. Part 2. Principles for determining the opening dimensions required for access into machinery (machinery parts) by body parts
GOST R EN 547-3-2009: Safety of machinery. Human body measurement. Part 3. Anthropometric data
GOST R EN 614-1-2003: Safety of machinery. Ergonomic design principles. Part 1. Terms, definitions and general principles
GOST R IEC 60204-1-2007: Safety of machinery. Electrical equipment of machines and mechanisms. Part 1. General requirements
GOST R IEC 61508-1-2007: Functional safety of electrical, electronic, programmable electronic safety-related systems. Part 1. General requirements
GOST R IEC 61508-3-2007: Functional safety of electrical, electronic, programmable electronic safety-related systems. Part 3. Software requirements
GOST R ISO 12100-1-2007: Safety of machinery. Basic concepts, general principles for design. Part 1. Basic terminology, methodology
GOST R ISO 12100-2-2007: Safety of machinery. Basic concepts, general principles for design. Part 2. Technical principles
GOST R ISO 13849-1-2003: Safety of machinery. Safety-related parts of control systems. Part 1. General principles for design
GOST R ISO 14122-1-2009: Safety of machinery - permanent means of access to machinery. Part 1. Choice of fixed means of access between two levels
GOST R ISO 14122-2-2010: Safety of machinery. Permanent means of access to machinery. Part 2. Working platforms and walkways.
GOST R ISO 14122-3-2009: Safety of machinery. Permanent means of access to machinery. Part 3. Stairs, stepladders and guard-rails.
GOST R ISO 14122-4-2009: Safety of machinery. Permanent means of access to machinery. Part 4. Vertical stairs
GOST R ISO 16156-2008: Machine-tools safety. Jaw chucks
|
Customers Who Viewed This Item Also Viewed:
 |
Tight and slack wooden barrels
Language: English |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Software for measuring instruments. Procedure for of certification. General provisions
Language: English |
Vegetable oils. General technical requirements
Language: English |
Current transformers. General specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
