GOST R 50838-2009
ГОСТ Р 50838-2009
|
|
Polyethylene pipes for the supply of gaseous fuel. Specifications
Трубы из полиэтилена для газопроводов. Технические условия
Status: Not effective - Canceled
This standard applies to polyethylene pressure pipes for underground gas pipelines of three types: - polyethylene pipes (nominal outer diameter d), including with marking strips; - polyethylene pipes with coextrusion layers on the outer and / or inner surfaces of the pipe (nominal outer diameter d with index n), where all layers have the same level of minimum long-term strength (MRS); - pipes made of polyethylene (nominal outer diameter d with index n) with an additional protective sheath of thermoplastic on the outer surface of the pipe, easily removable during installation. Pipes are intended for transportation of combustible gases according to GOST 5542, used as raw materials and fuels for industrial and household use with a maximum working pressure (MPA) of up to 1.2 MPa and a working gas temperature of up to 40 degrees. Celsius
Настоящий стандарт распространяется на напорные трубы из полиэтилена для подземных газопроводов трех типов: - трубы из полиэтилена (номинальным наружным диаметром d), в том числе с маркировочными полосами; - трубы из полиэтилена с соэкструзионными слоями на наружной и/или внутренней поверхностях трубы (номинальным наружным диаметром d с индексом n), где все слои имеют одинаковый уровень минимальной длительной прочности (MRS); - трубы из полиэтилена (номинальным наружным диаметром d с индексом n ) с дополнительной защитной оболочкой из термопласта на наружной поверхности трубы, легко удаляемой при монтаже. Трубы предназначены для транспортирования горючих газов по ГОСТ 5542, применяемых в качестве сырья и топлива для промышленного и коммунально-бытового использования при максимальном рабочем давлении (МОР) до 1,2 МПа и рабочей температуре газа до 40 град. по Цельсию
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/15/2009
SKU: RUSS73163
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
83 Rubber, technical rubber, asbestos and plastic industries »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Welding materials »
Welding regulations »
Admission Testing »
Welding regulations »
Documentation »
Welding regulations »
Mechanical Testing »
Welding regulations »
Main materials »
Polymers »
Welding regulations »
Welding materials »
Gases »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
4 Testing and control of products »
4.10 Testing and monitoring products of rubber and plastics industry »
4.10.2 Plastic Products »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.20 Plastic pipes »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.040 Pipelines and their components »
23.040.20 Plastic pipes »
ISO classifier »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.30 Plastic pipes, fittings not for liquids »
National standards »
83 RUBBER, RUBBER-TECHNICAL, ASBESTOTECHNICAL AND PLASTIC INDUSTRY »
83.140 Rubber and plastic products »
83.140.30 Plastic pipes, fittings not for liquids »
National Standards for KGS (State Standards Classification) »
Latest edition »
L Chemical products and rubber-asbestos products »
L2 Organic Chemical Products »
L26 Plastic products »
As a Replacement Of:
GOST R 50838-95: Polyethylene pipes for the supply of gaseous fuel. Specifications
The Document References:
Federal Law 184-FZ: About technical regulation
GN 2.2.5.1313-03: Maximum allowable concentrations (MACs) of harmful substances in occupational air
GOST 1.5-2001: Interstate system for standardization. Interstate standards, rules and recommendations on interstate standardization. General requirements for structure, drafting, presentation, content and indication
GOST 10354-82: Polyethylene film Specifications
GOST 11358-89: Dial-type thickness gauges and dial-type wall thickness gauges graduated in 0,01 and 0,1 mm. Specifications
GOST 11645-73: Plastics method of determination of melt flow index for thermoplastics
GOST 12.1.007-76: Noxious substances. Classification and general safety requirements
GOST 12.1.044-89: Fire and explosion hazard of substances and materials. Nomenclature of indices and methods of their determination
GOST 12.3.030-83: Occupation safety standards system. Safety requirements. Plastics processing
GOST 12162-77: Solid carbon dioxide
GOST 12423-66: Plastics. Standard atmospheres for conditioning and testing specimens
GOST 14192-96: Cargo marking
GOST 15139-69: Plastics. Methods for the determination of density (mass density)
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15846-2002: Production for transportation to the areas of Far North and similar regions. Packing, marking, transportation and storage
GOST 16272-79: Technical plasticized polyvinylchloride film. Specifications
GOST 16338-85: Low-pressure polyethylene. Specifications
GOST 166-89: Vernier callipers. Specifications
GOST 17.2.3.02-78: Regulations for establishing permissible emissions of noxious pollutants from industrial enterprises
GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements
GOST 22235-76: Freight cars for 1520 mm gauge main line railways. General requirements for safety in loading-unloading and shunting operations
GOST 24104-2001: Laboratory scales. General technical requirements
GOST 24157-80: Plastic pipes. Method of determination of the resistance to constant internal pressure
GOST 26311-84: Polyolefins. Method of determination of black content
GOST 26359-84: Polyethylene. Method for determination of volatile matters content
GOST 26653-90: Preparation of general cargoes for transportation. General requirements
GOST 27078-86: Thermoplastic pipes. Methods of determination of the tubes length after heating
GOST 2991-85: Wooden uncollapsible cases for weights up to 500 kg. General specifications
GOST 5530-2004: Packing and technical fabrics made of bast fibres. General specifications
GOST 5542-87: Natural fuel gases for industrial and domestic use
GOST 5583-78: Industrial and medical gaseous oxygen
GOST 6507-90: Micrometers. Specifications
GOST 7502-98: Measuring metal tapes. Specifications
GOST 8032-84: Preferred numbers and series of preferred numbers
GOST 9.708-83: Unified system of corrosion and ageing protection. Plastics. Ageing test methods on exposure to natural and artificial climatic factors
GOST 9293-74: Gaseous and liquid nitrogen. Specifications
GOST 949-73: Small and medium volume steel cylinders for gases for pp ≤ 19.6 MPa (200 kgf/cm2) Specifications
GOST ISO 11922-1-2006: Thermoplastics pipes for the conveyance of fluids. Dimensions and tolerances. Part 1. Metric series
GOST ISO 12162-2006: Thermoplastics materials for pipes and fittings for pressure applications. Classification and designation. Overall service coefficient
GOST ISO 161-1-2004: Thermoplastics pipes for the conveyance of fluids. Nominal outside diameters and nominal pressures. Metric series
GOST ISO 4065-2005: Thermoplastics pipes. Universal wall thickness table
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 1.5-2004: Standardization in the Russian Federation. National standards of the Russian Federation. Rules of structure, drafting, presentation and indication
GOST R 1.7-2008: Standardization in the Russian Federation. National standards of the Russian Federation. Rules of presentation and indication by development on the basis of application of international standards
GOST R 50838-95: Polyethylene pipes for the supply of gaseous fuel. Specifications
GOST R 52779-2007: Polyethylene fittings for gas pipelines. General specifications
GOST R 53228-2008: Non-automatic weighing instruments. Part 1. Metrological and technical requirements. Tests
GOST R 53652.1-2009: Thermoplastics pipes. Method for determination of tensile properties. Part 3. General requirement
GOST R 53652.3-2009: Thermoplastics pipes. Method for determination of tensile properties. Part 3. Polyolefin pipes
GOST R ISO 3126-2007: Plastics piping systems. Plastics components of piping systems. Determination of dimensions
The Document is Referenced By:
GOST R 54468-2011: Flexible pipes with thermal insulation for district heating, hot and cold water networks. General specifications
GOST R 55142-2012: Testing of welded joints of thermoplastic sheets and pipes. Test methods-Requirements
GOST R 55473-2013: Gas distribution systems. Requirements for gas distribution networks. Part 1. Polyethylene gas pipelines
GOST R 56290-2014: Gas distribution systems. Requirements to gas distribution networks. Part 3. Renovation
GOST R 58181-2018: Gas distribution systems. Requirements to gas distribution networks. Part 7. Polyethylene gas pipelines laid inside the existing pipeline
GOST R ISO 11413-2014: Plastics pipes and fittings. Preparation of test piece assemblies between a polyethylene pipe and an electrofusion fitting
GOST R ISO 11414-2014: Plastics pipes and fittings. Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
GOST R ISO 12176-1-2011: Plastics pipes and fittings. Equipment for fusion jointing polyethylene systems. Part 1. Butt fusion
MSN 42-01-2011: Gas distribution systems
ODM 218.3.083-2016: Guidelines for trenchless laying of road culvert pipes
RMD 40-20-2013 Sankt-Peterburg: Designing and installation pipelines for water supply and sewage systems in Saint-Petersburg
RMD 40-20-2016 Sankt-Peterburg: Installation of water supply and drainage networks in St. Petersburg
SP 249.1325800.2016: Design and construction of underground utilities by closed and cut-and-cover methods
SP 341.1325800.2017: Underground engineering communications. Lining of by a method of the horizontal directional drilling
SP 42-105-99: Quality control of welded joints of polyethylene gas pipelines
SP 424.1325800.2019: Pipelines trunk and field for oil and gas. Corrosion protection works by means of electrochemical protection and work execution control
|
Customers Who Viewed This Item Also Viewed:
 |
Industrial process measurement and control equipment. Reliability. General requirements and test methods
Language: English |
Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
Language: English |
System for ensuring the reliability and safety of construction sites. Loads and impacts. design standards
Language: English |
Heating, ventilation and air conditioning. Fire Safety Requirements
Language: English |
Reliability of atomic power stations and their equipment. General statements and reliability index nomenclature
Language: English |
Electromagnetic compatibility of technical equipment. Technical equipment for nuclear power plants. Requirement and test methods
Language: English |
Billets made of corrosion-resistant steels of 12Х18Н9Т, 12Х18Н10Т, 08Х18Н10Т, 10Х17Н13М2Т, 12Х18Н12Т and 03Х21Н32М3Б types.
Language: English |
Dependability in technics. Terms and definitions
Language: English |
System of products development and launching into manufacture. Technical assignment. Requirements to contents and form of presentation
Language: English |
Reliability in technology. Composition and general rules for setting reliability requirements
Language: English |
Rails of types P38 and P42. Technical conditions
Language: English |
Stainless corrosion resisting, heat-resisting and creep resisting steel and alloy on iron-nickel-based products. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
