GOST R 54803-2011
ГОСТ Р 54803-2011
|
|
High-pressure welded steel vessels. General technical requirements
Сосуды стальные сварные высокого давления. Общие технические требования
Status: Effective - Introduced for the first time. IUS 1-2014
This standard applies to steel welded vessels and devices operating under internal overpressure of up to 130 MPa (1300 kgf / cm sq.) At a wall temperature of at least minus 70 ° C and no more than 525 ° C, and establishes general technical requirements for design , materials, manufacturing, reconstruction, repair, methods of control and testing, acceptance and supply of vessels and apparatus used at hazardous production facilities. This standard does not limit the effect of GOST R 52630 within the scope of its application in the design and manufacture of steel welded vessels and apparatus. Norms and rules of design and manufacturing should be determined in accordance with the technological parameters of vessel operation and agreed with the customer.
Настоящий стандарт распространяется на стальные сварные сосуды и аппараты, работающие под внутренним избыточным давлением до 130 МПа (1300 кгс/см кв.) при температуре стенки не менее минус 70 °С и не более плюс 525 °С, и устанавливает общие технические требования к проектированию, материалам, изготовлению, реконструкции, ремонту, методам контроля и испытаний, приемке и поставке сосудов и аппаратов, применяемых на опасных производственных объектах. Настоящий стандарт не ограничивает действие ГОСТ Р 52630 в рамках области его применения при проектировании и изготовлении стальных сварных сосудов и аппаратов. Нормы и правила проектирования и изготовления должны быть определены в соответствии с технологическими параметрами эксплуатации сосуда и согласованы с заказчиком
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/13/2011
SKU: RUSS73585
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
71 Chemical industry »
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Welding materials »
Welding regulations »
welding equipment »
Welding regulations »
Welding staff »
Welding regulations »
Admission Testing »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Heat treatment »
Welding regulations »
Defects »
Welding regulations »
Assembly devices »
Welding regulations »
Welding work »
Manual welding »
Welding regulations »
Welding work »
Automatic welding »
Welding regulations »
Welding work »
Surfacing »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
Welding regulations »
Welding materials »
Electrodes »
Welding regulations »
Welding materials »
Fluxes »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
032/2013 TR CU. On safety of overpressure equipment »
Regulations and standards (to 032/2013 TR CU) »
ISO classifier »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
71.120.01 Equipment for chemical industry as a whole »
National standards »
71 CHEMICAL INDUSTRY »
71.120 Equipment for chemical industry »
71.120.01 Equipment for chemical industry as a whole »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G4 Machinery and equipment for heavy industry »
G40 Classification, nomenclature and general rules »
The Document References:
GOST 5264-80: Manual arc welding. Welding joints. Main types, design elements and dimensions
GOST 10052-75: Metal covered electrodes, for manual arc welding of high-alloyed steels with special properties. Types
GOST 10198-71: Boxes made of boards for cargoes weighing more than 200 and to 10,000 kg. Types. Dimensions of parts. General technical requirements
GOST 10493-81: Rigid and compensating
GOST 10494-80: Studs for flanged connections with lens-shaped seals for pn - 10-100 MPa (100-1000 kgf/sq sm). Technical requirements
GOST 10495-80: Hexagon nuts for flange joints for pn above 10 to 100 MPa (above 100 to 1000 kgf/cm2)
GOST 1050-88: Carbon structural quality steel gauged bars with special surface finish. General specifications
GOST 10-88: Inside micrometers. Specifications
GOST 10885-85: Hot-rolled two-ply corrosion-resistant steel sheets
GOST 11447-80: Locking studs for Py 10-100 MPa (100-1000 kgf/cm2). Technical requirements
GOST 11878-66: Austenitic steel bars. Methods for the determination of the ferrite-phase
GOST 12169-82: Steel blanks for oxygen cutting. Allowances
GOST 12971-67: Rectangular plates for machines and devices. Dimensions
GOST 14019-2003: Metallic materials. Bend test method
GOST 14192-96: Cargo marking
GOST 14771-76: Gas-shielded arc welding. Welded joints. Main types, design elements and dimensions
GOST 14782-86: Nondestructive testing. Welded joints. Ultrasonic methods
GOST 1497-84: Metals. Methods of tension test
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 15164-78: Electroslag welding. Welded joints. Main types, design elements and dimensions
GOST 15180-86: Flexible flat gaskets. Main parameters and dimensions
GOST 1577-93: Plate and broadband roll stock of construction fine steel.
GOST 16098-80: Welded joints of clad corrosion resistant steel. Main types, design elements and dimensions
GOST 162-90: Depth gauges. Specifications
GOST 17314-81: Devices for fastening thermal insulation of steel vessels and equipment. Design and dimensions. Technical requirements
GOST 18442-80: Non-destructive testing. Capillary methods. General requirements
GOST 19281-89: Rolled steel with increased strength. General specifications
GOST 19903-74: Hot-rolled steel sheets. Dimensions
GOST 2.109-73: Unified system for design documentation. Basic requirements for drawings
GOST 2.601-2006: Unified system for design documentation. Exploitative documents
GOST 20072-74: Heat-resistant steel
GOST 21105-87: Non-destructive testing. Method of magnetic particle testing
GOST 21650-76: Means of fastening tared and break bulk cargoes in the loads units. General requirements
GOST 2246-70: Welding steel wire. Specifications
GOST 22727-88: Rolled sheet. Ultrasonic test methods
GOST 22790-89: Assembly units and pipelines components, designed for рnom over 10 to 100 MPa (from 100 to 1000 kgf/cm2)
GOST 23055-78: Non-destructive testing. Fusion welding of metals. Welds classification by radiography testing results
GOST 23170-78: Packing for products of engineering industry. General requirements.
GOST 24297-87: Input inspection of products. General provisions.
GOST 24444-87: General assembly and technological requirements
GOST 24450-80: Magnetic non-destructive inspection. Terms and definitions
GOST 24522-80: Capillary non-destructive inspection. Terms and definitions
GOST 24634-81: Wooden boxes for export products. General specifications
GOST 24755-89: Vessels and apparatus. Norms and methods of strength calculation for openings reinforcement
GOST 25054-81: Forgings made of corrosion-resistant steels and alloys
GOST 25215-82: High-pressure vessels and apparatus. Shells and heads. Norms and methods of strength calculation
GOST 25347-82: Basic norms of interchangeability. Unified system of tolerances and fits. Tolerance zones and recommendable fits
GOST 25706-83: Magnifiers
GOST 26.008-85: Lettering for inscriptions applied by engraving method. Executive dimensions
GOST 2601-84: Welding of metals. Terms and definitions of basic concepts
GOST 26303-84: High-pressure vessels and apparatus. Threaded studs. Methods of strength calculation
GOST 26364-90: Ferritometers for austenitic steels. General specifications
GOST 26828-86: Instrumentation and machine building products. Marking
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 28759.1-90: Flanges of vessels and apparatus. Types and parameters
GOST 28759.5-90: Flanges of vessels and apparatuses
GOST 28759.6-90: Gaskets from nonmetallic materials.
GOST 28759.7-90: Asbestos-metal gaskets
GOST 28759.8-90: Metal gaskets of octagonal cross-section
GOST 2991-85: Wooden uncollapsible cases for weights up to 500 kg. General specifications
GOST 2999-75: Metals and alloys. Vickers hardness teat by diamond pyramid
GOST 30242-97: Imperfections in metallic fusion welds. Classification, designation and definitions
GOST 427-75: Measuring metal rules. Basic parameters and dimensions. Specifications
GOST 4543-71: Structural alloyed steel
GOST 550-75: Seamless steel tubes for petroleum processing and petrochemical industry. Specifications
GOST 5520-79: Carbon, low-alloy and alloy sheet steel for boilers and pressure vessels. Specifications
GOST 5632-72: High-alloy steels and corrosion-proof, heat-resisting and heat treated alloys. Grades
GOST 5640-68: Steel. Metallographic method for determination of microstructure of sheets and bands
GOST 5949-75: Gauged corrosion-resistant, heat-resistant and high-temperature steel shape
GOST 5959-80: Uncollapsable wooden sheet material boxes for weights to 200 kg mass. General specifications
GOST 6032-2003: Corrosion-resistant steels and alloys. Test methods of intercrystalline corrosion resistance
GOST 6533-78: Ellipsoidaldished heads flanged made of steel for vess els apparatus and boilers. Basis dimensions
GOST 6996-66: Welded joints. Methods of mechanical properties determination
GOST 7062-90: Carbon and alloyed steel forgings fabricated by press forging. Allowances and tolerances
GOST 7350-77: Plate, corrosion-resistant, heat-resistant, and high-temperature steel
GOST 7502-98: Measuring metal tapes. Specifications
GOST 7505-89: Steel stamping forgings. Tolerances, allowances and forging laps
GOST 7512-82: Nondestructive testing. Welded joints. Radiography method
GOST 7564-97: Rolled products general rules of samples, rough specimens and test pieces selection for mechanical and technological testing
GOST 7829-70: Carbon and alloyed steel forgings fabricated by hammer forging. Allowances and tolerances
GOST 8026-92: Levelling rules. Specifications
GOST 8273-75: Packing paper
GOST 8479-70: Structural carbon and alloy steel forgings
GOST 8713-79: Flux welding. Welded joints. Maih types design elements and dimensions
GOST 8731-74: Seamless hot-deformed steel pipes. Specifications
GOST 8733-74: Cold-formed and heat-formed seamless steel pipes. Technical requirements
GOST 8828-89: Base paper and two-layer waterproof packaging paper
GOST 9.014-78: Unified system of corrosion and ageing protection. Temporary corrosion protection of products. General requirements
GOST 9.032-74: Unified, system of corrosion and ageing protection. Paint coatings. Groups, technical requirements and designations
GOST 9.104-79: Unified system corrosion of corrosion and ageing protection. Paint coatings. Croups of operation conditions
GOST 9.105-80: Unified system of corrosion and ageing protection. Paints coatings. Classification and basic parameters of painting methods
GOST 9.401-91: Unified system of corrosion and ageing protection. Paint coatings. General requirements and methods of accelerated tests on resistance to the action of climatic factors.
GOST 9.402-2004: Unified system of corrosion and ageing protection. Paint coatings. Metal surface preparation for painting
GOST 9012-59: Metals. Method of Brinell hardness measurement
GOST 9087-81: Welding melted fluxes
GOST 9399-81: Threaded steel flanges for Pn 20-100 MPa (200-1000 kgf/sq sm). Specifications.
GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature
GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications
GOST 9467-75: Metal covered electrodes for manual arc welding of structural and heat-resistant steels. Types
GOST 9569-2006: Paraffined paper. Specifications
GOST 9617-76: Vessels and apparatus. Series of diameters.
GOST 9651-84: Metals. Methods of tension tests at elevated temperatures
GOST 9940-81: Seamless hot-deformed tubes made from corrosion-resistant steel
GOST 9941-81: Seamless cold- and warm-deformed tubes made from corrosion-resistant steel
GOST R 1.0-2012: Standardization in the Russian Federation. Basic provisions
GOST R 12.4.026-2001: Occupational safety standards system. Safety colors, safety signs and signal marking. Purpose and rules of application. General technical requirements and characteristics. Test methods
GOST R 2.901-99: Unified system for design documentation. Documentation to be sent abroad. General requirements
GOST R 50460-92: Mark of conformity for obligatory certification form, dimensions dnd technical requirements
GOST R 50599-93: Welded steel vessels and apparatus under high pressure. Non-destructive control while the manufacturing and operating
GOST R 52222-2004: Fused fluxes for automatic welding. Specifications
GOST R 52376-2005: Heat-resistant spiral-wound gaskets. Types. Main dimensions
GOST R 52630-2012: Steel welded vessels and apparatus. General specifications.
GOST R 52857.10-2007: Vessels and apparatus. Norms and methods of strength calculation. Vessels and apparatus involving hydrogen sulphide media
GOST R 52857.11-2007: Vessels and apparatus. Norms and methods of strength calculation. Method of strength calculation of shells and heads according to weld misalignment, angular misalignment and shell nonroundness
GOST R 52857.1-2007: Vessels and apparatus. Norms and methods of strength calculation. General requirements
GOST R 52857.2-2007: Vessels and apparatus. Norms and methods of strength calculation. Calculation of cylindric and conic, shells convex and flat bottoms and covers
GOST R 52857.3-2007: Vessels and apparatus. Norms and methods of strength calculation. Reinforcement of openings in shells and heads under internal and external pressure. Strength calculation of shells and heads under external static loads on the nozzle
GOST R 52857.4-2007: Vessels and apparatus. Norms and methods of strength calculation. Stength and leak-tightness calculation of flange joints
GOST R 52857.5-2007: Vessels and apparatus. Norms and methods of strength calculation. Calculation of shells and heads from influence of support loads
GOST R 52857.6-2007: Vessels and apparatus. Norms and methods of strength calculation. Strength calculation under low-cyclic loads
GOST R 52857.7-2007: Vessels and apparatus. Norms and methods of strength calculation. Heat-exchangers
GOST R 52857.8-2007: Vessels and apparatus. Norms and methods of strength calculation. Jacketed vessels and apparatus
GOST R 52857.9-2007: Vessels and apparatus. Norms and methods of strength calculation. Determination of stresses at nozzle-to-shell and head junctions under action of pressure and external loads on the nozzle
GOST R 53442-2009: Basic norms of interchangeability. Geometrical product specifications. Tolerances of form, orientation, location and run-out
GOST R 53677-2009: Petroleum and natural gas industries. Shell-and-tube heat eхchangers. Technical requirements
GOST R 53684-2009: Columns. Technical requirements
OST 108.030.113-87: Carbon and alloy steel forgings for thermal and nuclear power stations equipment and pipelines. Technical specifications.
PB 03-576-03: Regulations of design and safe operation of pressure vessels
RD 03-606-03: Instructions for visual and measuring control
The Document is Referenced By:
Decision 96: On the list of international and regional (interstate) standards, and in their absence - national (state) standards, the application of which on a voluntary basis to ensure compliance with the requirements of technical regulations of the Customs Union "On safety of equipment operating under excess pressure" (TR TS 032/2013), and the list of international and regional (interstate) standards, and in their absence - national (state) standards, containing rules and methods of research (tests) and
GOST 34595-2019: Mining engineering. Pneumatic impulse cartridges. General technical requirements. Test methods
GOST R 55597-2013: High pressure vessels and apparatus. Norms and methods of strength calculation. Reinforcement of openings in shells and heads external pressure. Strength calculation under external static loads on the nozzle
PNST 741-2024: Oil and gas industry. Subsea production systems. High pressure vessels
|
Customers Who Viewed This Item Also Viewed:
 |
Limit dimension deviation from 0,1 to 10000 mm and surface shape and arrangement allowances, not specified on drawings.
Language: English |
Rules of development, coordination, approval and composition of technical and economic assessment for construction
Language: English |
Mineral fertilizers. Method for determination of dynamic strength and attrition
Language: English |
United power system and isolated power systems. Operative-dispatch management. Frequency control and control of active power. Norms and requirements
Language: English |
Diesel fuel EURO. Specifications
Language: English |
Inch thread with a profile angle of 55 degrees
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
