GOST 25347-2013
ГОСТ 25347-2013
|
|
Basic norms of interchangeability. Geometrical product specifications. System for tolerances on linear sizes. Series of tolerances, limit deviations for holes and shafts
Основные нормы взаимозаменяемости. Характеристики изделий геометрические. Система допусков на линейные размеры. Ряды допусков, предельные отклонения отверстий и валов
Status: Effective - Supersedes. IUS 3-2015
The standard contains the numerical values of the limit deviations of the holes and shafts for tolerance classes of general use, calculated according to GOST 25346. The standard shows the values of the upper limit deviations of the holes ES and the shafts es, as well as the lower limit deviations of the holes EI and shafts ei. In the standard, for the purpose of simplification, only details representing circular cylinders are considered in detail, since such details are important. However, tolerances and deviations given in the standard can also apply to parts whose cross-section is not a circle.
Стандарт содержит числовые значения предельных отклонений отверстий и валов для классов допусков общего применения, вычисленные по ГОСТ 25346. В стандарте приведены значения верхних предельных отклонений отверстий ES и валов es, а также нижних предельных отклонений отверстий EI и валов ei. В стандарте с целью упрощения подробно рассмотрены только детали представляющие собой круговые цилиндры, т.к. такие детали имеют важное значение. Однако допуски и отклонения, приведенные в стандарте, также могут относиться и к деталям, сечение которых не является окружностью.
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
2/18/2014
SKU: RUSS74066
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
17 Metrology and measurements. Physical phenomena »
Standards for pipe fittings (TPA) »
8. Piping valves (TPA) design »
8.1 General design issues piping valves (TPA) »
8.1.2 Interchangeability and other design requirements »
PromExpert »
SECTION I. TECHNICAL REGULATION »
V Testing and control »
3 Activities of testing laboratories »
3.2 Technical equipment of testing laboratories »
3.2.2 Measuring instruments and test equipment »
3.2.2.2 Instruments for measuring pressure, volume, flow, level, time and mechanical quantities »
ISO classifier »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.040 Linear and angular measurements »
17.040.01 Linear and angular measurements in general »
National standards »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.040 Linear and angular measurements »
17.040.01 Linear and angular measurements in general »
ISO classifier »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.040 Linear and angular measurements »
17.040.10 Tolerances and landings »
National standards »
17 METROLOGY AND MEASUREMENTS. PHYSICAL PHENOMENA »
17.040 Linear and angular measurements »
17.040.10 Tolerances and landings »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G0 General rules and regulations for engineering »
G02 Norms of calculation and design »
National Standards for OKSTU »
SYSTEMS OF GENERAL TECHNICAL AND ORGANIZATIONAL-METHODOLOGICAL STANDARDS »
Tolerances and landings. Surface cleanliness »
As a Replacement Of:
GOST 25347-82: Basic norms of interchangeability. Unified system of tolerances and fits. Tolerance zones and recommendable fits
The Document References:
GOST 25346-2013: Basic norms of interchangeability. Geometrical product specifications. Code system for tolerances on linear sizes. General provisions, tolerances, deviations and fits
The Document is Referenced By:
GOST 1335-84: Rubber brake hoses with thread reinforcement for railroad and subway transport without couplings
GOST 16556-2016: Ground connections for movable electric units. General specifications
GOST 23190-2018: Book-selling furniture. General specifications
GOST 23508-2018: Book-selling furniture for storage facilities. General specifications
GOST 25346-2013: Basic norms of interchangeability. Geometrical product specifications. Code system for tolerances on linear sizes. General provisions, tolerances, deviations and fits
GOST 31610.0-2014: Explosive atmospheres. Part 0. Equipment. General requirements
GOST 32601-2022: Centrifugal pumps for oil, petrochemical and gas industry. General technical requirements
GOST 33746-2016: Returnable polymeric boxes. General specifications
GOST 34347-2017: Steel welded vessels and apparatus. General technical conditions
GOST 34905.1-2022: Rolling Bearings. Methods of measurement of vibration. Part 1. General provisions
GOST 34905.2-2022: Rolling Bearings. Methods of measurement of vibration. Part 2. Radial and angular contact ball bearings
GOST 34905.3-2022: Rolling Bearings. Methods of measurement of vibration. Part 3. Roller spherical and tapered bearings
GOST 34905.4-2022: Rolling Bearings. Methods of measurement of vibration. Part 4. Cylindrical bearings
GOST ISO 4759-1-2015: Tolerances for fasteners. Part 1. Иolts, screws, studs and nuts. Product grades A, B and C
GOST R 50.05.02-2018: Conformity assessment system for the use of nuclear energy. Conformity assessment in the form of examination. Unified procedures. Ultrasonic examination of welded joints and cladded surfaces
GOST R 51177-2017: Overhead line hardware. General technical requirements
GOST R 53791-2010: Resources saving. Stages of technological cycle. General principles
GOST R 55601-2013: Heat exchanger apparatuses and air cooling apparatuses. Tube expanding in tube-sheets. General technical requirements
GOST R 56615-2015: Resources saving. Indices of materials consumption and materials affection. Guidance by establishment criterions of choice
GOST R 57351-2016: Building steel structures. General specifications
GOST R 57620-2017: Dentistry. Refractory investment and die material. Technical requirements. Test methods
GOST R 58514-2019: Building levels. Technical conditions
GOST R 58518-2019: Steel construction hammers. Technical conditions
GOST R 58519-2019: Rules, graters and graters. Technical conditions
GOST R 60.3.4.1-2017: Robots and robotic devices. Manipulating industrial robots. Mechanical interfaces. Plates
GOST R 60.3.4.2-2017: Robots and robotic devices. Manipulating industrial robots. Mechanical interfaces. Shafts
GOST R 70352-2022: Fittings for overhead power lines up to 1 kV with self-supporting insulated wires. General specifications
GOST R 70595-2022: Shipboard fittings. General specifications
GOST R 70726-2023: Modular swimming pools. General technical conditions
GOST R ISO 10303-47-2019: Industrial automation systems and their integration. Presentation and exchange of product data. Part 47. Integrated generalized resource. Shape Change Tolerances
GOST R ISO 9766-2019: Drills with mechanical fastening of cutting inserts. Cylindrical shanks with flat. Main dimensions
SDOS-11-2015: Guidelines on the procedure for conducting ultrasonic testing of metal structures of technical devices, buildings and structures
SP 46.13330.2012: Bridges and pipes
ST TsKBA 019-2012: Pipe fittings. Thermally expanded graphite based seals. General technical requirements
ST TsKBA 083-2016: Pipeline fittings. Multi-layered bellows made of alloy ВТ1-0. General technical specifications
|
Customers Who Viewed This Item Also Viewed:
 |
Liquids for aircrafts systems. Method for determination thermo oxidizing stability and corrosion activity
Language: English |
Plastics structured-wall pipes and their fittings for sewerage systems outside the buildings. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
