GOST R 56001-2014
ГОСТ Р 56001-2014
|
|
Pipeline valves for objects of gas industry. General specifications
Арматура трубопроводная для объектов газовой промышленности. Общие технические условия
Status: Effective - Introduced for the first time. IUS 8-2015
This standard applies to pipeline valves with nominal diameters up to DN 1400 at nominal pressures up to PN 400 used at gas production, underground storage, processing, transportation, distribution and consumption of gas, and establishes general technical requirements for shut-off, control, safety and return pipeline during its design, manufacture, acceptance, testing, transportation, installation, operation, repair, storage and disposal. This standard does not apply to wellhead (fountain) valves, condensate pipes fittings, pipeline valves for working medium containing hydrogen sulfide (H2S) more than 7 mg / m3, as well as fittings for offshore gas pipelines and gas pipelines intended for transporting liquefied gases. This standard can be used to confirm compliance.
Настоящий стандарт распространяется на трубопроводную арматуру с номинальными диаметрами до DN 1400 на номинальные давления до PN 400, применяемую на объектах добычи, подземного хранения, переработки, транспортировки, распределения и потребления газа, и устанавливает общие технические требования к запорной, регулирующей, предохранительной и обратной трубопроводной арматуре при ее проектировании, изготовлении, приемке, испытаниях, транспортировке, монтаже, эксплуатации, ремонте, хранении и утилизации. Настоящий стандарт не распространяется на устьевую (фонтанную) арматуру, арматуру конденсатопроводов, на трубопроводную арматуру для рабочей среды с содержанием сероводорода (Н2S) более 7 мг/м3, а также арматуру морских газопроводов и газопроводов, предназначенных для транспортировки сжиженных газов. Настоящий стандарт может быть использован для подтверждения соответствия
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
4/17/2014
SKU: RUSS74103
The Product is Contained in the Following Classifiers:
Welding regulations »
Welding work »
Welding regulations »
Main materials »
Welding regulations »
Pipelines »
Welding regulations »
Metal structures »
Welding regulations »
Welding materials »
Welding regulations »
Admission Testing »
Welding regulations »
Documentation »
Welding regulations »
Non-destructive control »
Welding regulations »
Mechanical Testing »
Welding regulations »
Heat treatment »
Welding regulations »
Defects »
Welding regulations »
Welding work »
Surfacing »
Welding regulations »
Welding work »
Dusting »
Welding regulations »
Main materials »
Steel, cast iron »
Welding regulations »
Welding materials »
Gases »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
032/2013 TR CU. On safety of overpressure equipment »
Regulations and standards (to 032/2013 TR CU) »
Standards for pipe fittings (TPA) »
3. Piping valves (TPA) standards for industries »
3.4 For pipeline transport of oil and gas »
Standards for pipe fittings (TPA) »
3. Piping valves (TPA) standards for industries »
3.2 For gas industry »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.060 Pipe fittings »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.060 Pipeline valves »
ISO classifier »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.060 Pipe fittings »
23.060.01 Pipe fittings in general »
National standards »
23 HYDRAULIC AND PNEUMATIC SYSTEMS AND GENERAL PURPOSE COMPONENTS »
23.060 Pipeline valves »
23.060.01 Pipe fittings in general »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.180 Equipment for oil and gas industry »
National standards »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.180 Equipment for oil and gas industry »
ISO classifier »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.180 Equipment for oil and gas industry »
75.180.01 Equipment for oil and gas industry in general »
National standards »
75 EXTRACTION AND PROCESSING OF OIL, GAS AND RELATED PRODUCTION »
75.180 Equipment for oil and gas industry »
75.180.01 Equipment for oil and gas industry in general »
The Document References:
GN 2.2.5.1313-03: Maximum allowable concentrations (MACs) of harmful substances in occupational air
GOST 10051-75: Metal covered electrodes for manual arc surfacing of upper layers with special properties types
GOST 10549-80: Screw thread runout. Washout threads, total thread runouts, undercuts and chamfers
GOST 10877-76: Preservative oil K-17
GOST 11881-76: Controllers acting without
GOST 12.1.005-88: General sanitary requirements for working zone air
GOST 12.1.007-76: Noxious substances. Classification and general safety requirements
GOST 12.2.085-2002: Vessels working under pressure. Safety valves. Safety requirements
GOST 12.3.009-76: Occupational safety standards system. Loading and unloading works General safety requirements
GOST 12678-80: Direct-acting pressure regulators. Main parameters
GOST 12893-2005: Single-seated, double-seated and cage control valves. General specifications
GOST 12971-67: Rectangular plates for machines and devices. Dimensions
GOST 14187-84: Plug valves. Overroll dimensions
GOST 14192-96: Cargo marking
GOST 14254-96: Degrees of protection provided by enclosures (IP Code)
GOST 15.309-98: System of product development and launching into manufacture. Test and acceptance of produced goods. Principal positions
GOST 15.311-90: System of product development and launching into manufacture. Launching of products under foreign companies technical documents
GOST 15150-69: Machines, instruments and other industrial products. Modifications for different climatic regions. Categories, operating, storage and transportation conditions as to environment climatic aspects influence
GOST 16037-80: Welded joints in steel pipelines. Main types, design elements and dimensions
GOST 16118-70: Cylindrical helical compression (extension) springs made of round steel. Specifications
GOST 16587-71: Safety valves, control valves and pressure regulators. Face-to-face lengths
GOST 17516.1-90: Electrical articles. General requirement for environment mechanical stability
GOST 1778-70: Steel. Metallographic methods for the determination of non-metallic inclusions
GOST 2.601-2006: Unified system for design documentation. Exploitative documents
GOST 2.610-2006: Unified system for design documentation. Rules for making exploitative documents
GOST 20700-75: Bolts, studs, nuts and washers for flanged and anchor connections, corks and yokes with medium temperature from 0 to 650 °C. Specifications
GOST 21345-2005: Ball, lifting-plug and cylindrical cocks for nominal pressure at most PN 250. General specifications
GOST 24297-87: Input inspection of products. General provisions.
GOST 24643-81: Basic norms of interchangeability. Tolerances of form and position of surfaces. Numerical values
GOST 24705-2004: Вasic norms of interchangeability. Metric screw thread. Basic dimensions
GOST 24737-81: Basic norms of interchangeability. Trapezoidal single-start screw thread. Basic dimensions
GOST 26304-84: Industrial pipeline valves supplied
GOST 263-75: Rubber. Method for the determination of Shore A hardness
GOST 27.310-95: Dependability in techniques. Failure mode, effects and criticality analysis. Basic principles
GOST 2789-73: Surface roughness. Parameters and characteristics
GOST 28338-89: Nominal bores (nominal sizes)
GOST 28908-91: Ball valves and disk gate valves. End-to-end (face-to-face) dimensions
GOST 30546.1-98: General requirements for machines, instruments and other industrial products and calculation methods for their complex structures as to seismic stability
GOST 30893.1-2002: Basic norms of interchangeability. General tolerances. Limit deviations for linear and angular dimensions without tolerance indications
GOST 30893.2-2002: Basic norms of interchangeability. General tolerances. Tolerances of form and position for features without individual tolerance indications
GOST 31294-2005: Direct-acting safety valves. General specifications
GOST 3326-86: Stop valves, check lift and swing valves. Overall dimensions
GOST 356-80: Valves and details for piping. Pressures conditional, test and operational. Lines.
GOST 3706-93: Gate valves. End-to-end lengths
GOST 5639-82: Steel and alloys. Methods for detection and determination of grain size
GOST 5762-2002: Pipeline industrial valves. Gate valves PN<=250. General specifications
GOST 6996-66: Welded joints. Methods of mechanical properties determination
GOST 7192-89: Constant-speed electrical actuating mechanisms, ssi
GOST 8479-70: Structural carbon and alloy steel forgings
GOST 8908-81: Basic norms of interchangeability. Standard angles and angle tolerances
GOST 9.014-78: Unified system of corrosion and ageing protection. Temporary corrosion protection of products. General requirements
GOST 9150-2002: Basic norms of interchangeability. Metric screw threads. Profile
GOST 9399-81: Threaded steel flanges for Pn 20-100 MPa (200-1000 kgf/sq sm). Specifications.
GOST 9454-78: Metals. Method for testing the impact strength at the low, room and high temperature
GOST 9466-75: Covered metal electrodes for manual arc welding of steels and deposition. Classification and general specifications
GOST R 15.201-2000: System of product development and launching into manufacture. Products of industrial and technical designation. Procedure of product development and launching into manufacture
GOST R 50753-95: Cylindrical helical compression (extension) springs made of special steels and alloy. General specifications
GOST R 51164-98: Steel pipe mains. General requirements for corrosion protection
GOST R 51330.0-99: Explosionproof electrical apparatus. Part 0. General requirements
GOST R 51901.12-2007: Risk management. Procedure for failure mode and effects analysis
GOST R 52079-2003: Steel welded pipes for trunk gas pipelines, oil pipelines and oil products pipelines. Specifications
GOST R 52568-2006: Steel pipes with defensive covering for main gas and oil pipelines. Specifications
GOST R 52760-2007: Pipeline valves. Requirements for the marking and distinctive painting
GOST R 52857.1-2007: Vessels and apparatus. Norms and methods of strength calculation. General requirements
GOST R 52857.2-2007: Vessels and apparatus. Norms and methods of strength calculation. Calculation of cylindric and conic, shells convex and flat bottoms and covers
GOST R 52857.3-2007: Vessels and apparatus. Norms and methods of strength calculation. Reinforcement of openings in shells and heads under internal and external pressure. Strength calculation of shells and heads under external static loads on the nozzle
GOST R 52857.4-2007: Vessels and apparatus. Norms and methods of strength calculation. Stength and leak-tightness calculation of flange joints
GOST R 52857.5-2007: Vessels and apparatus. Norms and methods of strength calculation. Calculation of shells and heads from influence of support loads
GOST R 52857.6-2007: Vessels and apparatus. Norms and methods of strength calculation. Strength calculation under low-cyclic loads
GOST R 53402-2009: Pipeline valves. Methods of control and testing
GOST R 53671-2009: Pipeline valves. Swing and lift check valves. General specifications
GOST R 53672-2009: Pipeline valves. General safety requirements
GOST R 53674-2009: Pipeline valves. Nomenclature of characteristics. Check-lists for design and order
GOST R 54432-2011: Flanges for valves, fittings, and pipelines for pressure from PN 1 to PN 200. Design, dimensions and general technical requirements
GOST R 54808-2011: Pipeline valves. Leakage rates of valves.
GOST R 55509-2013: Pipeline valves. Metals used in pipeline valves production. Basic requirements for choice of materials
GOST R 55510-2013: Pipeline valves. Drives of rotary action. The connecting dimensions
GOST R 55511-2013: Pipeline valves. Electric actuators. General specifications
GOST R ISO 3183-2009: Steel pipes for pipelines of petroleum and natural gas industries. General specifications
PB 03-273-99: Rules for qualification test of welders and welding production specialists
PB 03-585-03: Process Pipelines Design and Safe Operation Rules
PNAE G-7-025-90: Steel castings for nuclear plants. Rules of control
POT R M-016-2001: Inter-Industry Occupational Safety and Health Regulations (Safety Regulations) for Operation of Electrical Installations
RD 03-495-02: Procedures for the qualification test of welders and welding work specialists
RD 03-615-03: Order of welding technologies application at engineering devices production, installation, repair and reconstruction for unsafe industrial objects.
RD 302-07-279-89: Pipe fittings. Methods of assessing the reliability of the test results and (or) operation
Safety Guide: Recommendations on arrangement and safe operation of process pipelines
Safety Guide: Recommendations on technical diagnostics of welded vertical cylindrical tanks for oil and petroleum products
ST TsKBA 001-2003: Pipe fittings. General Fire Test Requirements
ST TsKBA 010-2004: Pipe fittings. Forgings, stampings and rolled products. Technical requirements
ST TsKBA 013-2007: Pipe fittings. Welding of fittings to the pipeline. Technical requirements
ST TsKBA 025-2006: Pipe fittings. Welding and quality control of welded joints. Technical requirements
ST TsKBA 028-2007: Pipe fittings. Periodic testing. General requirements
ST TsKBA 031-2009: Pipe fittings. Passport. Development and design rules
ST TsKBA 041-2008: Pipe fittings. Input control of materials, semi-finished products and components
ST TsKBA 049-2009: Pipe fittings. Ensuring reliability in manufacturing
ST TsKBA 082-2009: Pipe fittings. Input control
ST TsKBA 099-2011: Pipe fittings. Repairs. Organization of repair and general repair manual
Technical regulations of the Customs Union 012/2011: On the safety of equipment for work in explosive atmospheres
Technical regulations of the Customs Union TR TS 004/2011: About the safety of low voltage equipment
The Document is Referenced By:
Decision 96: On the list of international and regional (interstate) standards, and in their absence - national (state) standards, the application of which on a voluntary basis to ensure compliance with the requirements of technical regulations of the Customs Union "On safety of equipment operating under excess pressure" (TR TS 032/2013), and the list of international and regional (interstate) standards, and in their absence - national (state) standards, containing rules and methods of research (tests) and
GOST 12.2.063-2015: Pipeline valves. General safety requirements
GOST 34027-2016: Gas supply system. Gas main pipeline transportation. Mechanical safety. Assigning of safe operation life for linear part of gas main pipeline
GOST 4666-2015: Pipeline accessories. Requirements for marking
GOST R 56005-2014: Pipeline valves. Reliability and safety practice for engineering and production by quality function deployment applying
GOST R 56006-2014: Pipeline valves. Testing and acceptance on objects of the gas main pipelines before commissioning. General technical requirements
|
Customers Who Viewed This Item Also Viewed:
 |
Controllers acting without
Language: English |
Building materials. Methods for combustibility test
Language: English |
Building materials spread flame test method
Language: English |
Polyvinyl chloride insulated cables of rated voltages up to and including 450/750 V. Non-sheathed cables for fixed wiring
Language: English |
Clear sheet glass. Specifications
Language: English |
Natural gas. Methods of calculation of physical properties. Calculation of physical properties on base information on density of standards conditions and nitrogen and carbon dioxide contents
Language: English |
Steel welded vessels and apparatus. General technical conditions
Language: English |
System of Standards for Occupational Safety and Health (SSBT). Personal protective equipment for respiratory organs. Self-rescuers insulating on chemically bound or with compressed oxygen. Technical requirements. Test methods. Marking. Sampling rules
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
