GOST R 50030.2-2010
ГОСТ Р 50030.2-2010
|
|
Low-voltage switchgear and control gear. Part 2. Circuit-breakers
Аппаратура распределения и управления низковольтная. Часть 2. Автоматические выключатели
Status: Effective
This standard applies to circuit breakers, the main contacts of which are designed for switching circuits with voltage up to 1000 V AC or 1500 V DC, and also contains additional requirements for switches with built-in fuses. The standard is used for switches with any rated currents, various designs and methods of application. This standard establishes: a) the characteristics of switches; b) the conditions that the switches must meet in relation to: 1) the performance and behavior in normal operation; 2) health and behavior in case of overloads, short circuits, including coordination during operation (selectivity and backup protection); 3) electrical insulation properties; c) tests aimed at verifying compliance with these conditions, and the methodology for conducting such tests; d) information to be marked on or supplied with the devices
Настоящий стандарт распространяется на автоматические выключатели, главные контакты которых предназначены для коммутации цепей напряжением до 1000 В переменного или 1500 В постоянного тока, а также содержит дополнительные требования для выключателей со встроенными плавкими предохранителями. Стандарт применяют для выключателей с любыми номинальными токами, различных конструкций и способов применения. Настоящий стандарт устанавливает: a) характеристики выключателей; b) условия, которым должны удовлетворять выключатели, применительно к: 1) работоспособности и поведению в нормальном режиме эксплуатации; 2) работоспособности и поведению при перегрузках, коротких замыканиях, в том числе к координации при эксплуатации (селективности и резервной защите); 3) электроизоляционным свойствам; c) испытания, направленные на проверку выполнения этих условий, и методику проведения таких испытаний; d) информацию, которая должна быть маркирована на аппаратах или поставляться вместе с ними
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
11/30/2010
SKU: RUSS74188
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
29 Electrical Engineering »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
004/2011 TR CU. About safety of low voltage equipment »
Regulations and standards (to TR CU 004/2011) »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
020/2011 TR CU. Electromagnetic compatibility of technical means »
Regulations and standards (to ТР ТС ТС 020/2011) »
ISO classifier »
29 ELECTRICAL ENGINEERING »
29.130 Switching and control equipment »
29.130.20 Low-voltage switching equipment and control equipment »
National standards »
29 ELECTRICAL ENGINEERING »
29.130 Switching and control equipment »
29.130.20 Low-voltage switching equipment and control equipment »
National Standards for KGS (State Standards Classification) »
Latest edition »
E Power and electrical equipment »
E7 Electrical apparatus and fittings »
E71 Devices with voltage up to 1000 V »
National Standards for OKSTU »
ELECTRICAL EQUIPMENT AND MATERIALS »
Automatic circuit breakers with a maximum rated current of up to 1000 A in plastic cases (automatic devices) »
As a Replacement Of:
GOST R 50030.2-99: Low-voltage switchgear and controlgear. Part 2. Circuit-breakers
The Document References:
Federal Law 184-FZ: About technical regulation
GOST 17441-78: Electrical contact connections. Rules of acceptance and test methods
GOST 17441-84: Electrical contact connections. Acceptance and methods of tests
GOST 27473-87: Method for determining the comparative and the proof tracking indices of solid insulating materials under moist conditions
GOST 27484-87: Fire hazard testing. Test methods. Needle-flame test
GOST 28216-89: Basic environmental testing procedures. Part 2. Tests. Test Db and guidance: damp heat, cyclic (12 + 12 hour cycle)
GOST 28779-90: Solid electrical insulating materials. Methods of test for the determination of the flammability when exposed to an igniting source
GOST 30012.1-2002: Direct acting indicating analogue electrical measuring instruments and their accessories. Part 1. Definitions and general requirements common to all parts
GOST 9.005-72: Unified system of corrosion and ageing protection. Metals, alloys, metallic and non-metallic coatings. Permissible and impermissible contacts with metals and non-metals
GOST R 1.0-2004: Standardization in the Russian Federation. Basic provisions
GOST R 1.5-2004: Standardization in the Russian Federation. National standards of the Russian Federation. Rules of structure, drafting, presentation and indication
GOST R 50030.1-2007: Low-voltage switchgear and controlgear. Part 1. General rules
GOST R 50030.2-99: Low-voltage switchgear and controlgear. Part 2. Circuit-breakers
GOST R 50030.3-99: Low -voltage switchgear and controlgear. Pat 3. Switchers, disconnectors, switch-disconnectors and fure-combination units
GOST R 50030.4.1-2002: Low-voltage switchgear and controlgear. Part 4-1. Contactors and motor-starters. Electromechanical contactors and motor-starters
GOST R 50030.5.1-2005: Low-voltage switchgear and controlgear. Part 5. Control circuit devices and switching elements. Section 1. Electromechanical control circuit devices
GOST R 50031-99: Circuit-breakers for equipment (CBE)
GOST R 50339.0-2003: Low-voltage fuses. Part 1. General requirements
GOST R 50339.0-92: Low-voltage fuses. General requirements
GOST R 50339.1-92: Low-voltage fuses. Part 2. Supplementary requirements for fuses for industrial application
GOST R 50339.2-92: Low-voltage fuses. Part 2-1. Supplementary requirements for fuses for industrial application. Section 1-3
GOST R 50339.3-92: Low-voltage fuses. Part 3. Supplementary requirements for fuses for household use
GOST R 50345-2010: Electrical accessories. Circuit-breakers for overcurrent protection for household and similar installations. Part 2. Circuit-breakers for a.c. operation
GOST R 50807-95: Residual current operated protective devices. General requirements and test methods
GOST R 51317.3.2-2006: Electromagnetic compatibility of technical equipment. Harmonic current emissions (equipment input current <=16 A per phase). Limits and test methods.
GOST R 51317.3.3-2008: Electromagnetic compatibility of technical equipment. Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems. Equipment with rated current <= 16 A (per phase) and not subject to conditional connection. Limits and test methods
GOST R 51317.3.3-99: Electromagnetic compatibility of technical equipment. Voltage fluctuation and flicker impressed on low-voltage supply systems by equipment with rated current <=16 A. Limits and test methods
GOST R 51317.4.11-2007: Electromagnetic compatibility of technical equipment. Voltage dips, short interruptions and voltage variations immunity. Requirements and test methods
GOST R 51317.4.11-99: Electromagnetic compatibility of technical equipment. Immunity to dynamic changes of power supply voltage. Requirements and test methods
GOST R 51317.4.13-2006: Electromagnetic compatibility of technical equipment. Immunity to non-sinusoidal distortion of supply voltage including mains signalling. Requirements and test methods
GOST R 51317.4.2-2010: Electromagnetic compatibility of technical equipment. Electrostatic discharge immunity. Requirements and test methods.
GOST R 51317.4.2-99: Electromagnetic compatibility of technical equipment. Immunity to electrostatic discharge. Requirements and test methods
GOST R 51317.4.3-2006: Electromagnetic compatibility of technical equipment. Radio-frequency electromagnetic field immunity. Requirements and test methods.
GOST R 51317.4.3-99: Electromagnetic compatibility of technical equipment. Radiated, radio-frequency, electromagnetic field immunity. Requirements and test methods
GOST R 51317.4.4-2007: Electromagnetic compatibility of technical equipment. Immunity to nanosecond impulsive disturbance. Requirements and test methods
GOST R 51317.4.4-99: Electromagnetic compatibility of technical equipment. Immunity to electrical fast transient/burst. Requirements and test methods
GOST R 51317.4.5-99: Electromagnetic compatibility of technical equipment. Microsecond high energy pulse disturbance immunity. Requirements and test methods
GOST R 51317.4.6-99: Electomagnetic compatibility of technical equipment. Immunity to conducted disturbance induced by radio-frequency fields. Requirements and test methods
GOST R 51318.11-2006: Electromagnetic compatibility of technical equipment. Industrial, scientific, medical and domestic (ISMD) high-frequency equipment. Radio disturbance. Limits and methods of measurement
GOST R 51318.11-99: Electromagnetic compatibility of technical equipment. Radio disturbance from industrial, scientific, medical and domestic (ISMD) radio-frequency equipment. Limits and test methods
GOST R 51318.22-2006: Electromagnetic compatibility of technical equipment. Information technology equipment. Man-made radio disturbance. Limits and methods of measurement
GOST R 51318.22-99: Electromagnetic compatibility of technical equipment. Man-made radio disturbance from information technology equipment. Limits and test methods
GOST R 51321.1-2007: Low-voltage switchgear and control gear assemblies. Part 1. Type-tested and partially type-tested assemblies. General technical requirements and test methods
GOST R 51326.1-99: Residual current operated circuit-breakers without integral overcurrent protection for household and similar uses (RCCB's). Part 1. General requirements and test methods
GOST R 51327.1-2010: Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs). Part 1. General rules and test methods
GOST R 52161.1-2004: Safety of household and similar electrical appliances. Part 1. General requirements
The Document is Referenced By:
GOST 12.2.091-2002: Safety requirements for electrical equipment for measurement, control and laboratory use. Part 1. General requirements
GOST 33798.3-2016: Railway applications. Electric equipment for rolling stock. Part 3. Electrotechnical components. Rules for d.c. circuit-breakers
GOST 33807-2016: Safety of attractions. General requirements
GOST IEC 60947-3-2016: Low-voltage switchgear and controlgear. Part 3. Switches, disconnectors, switch-disconnectors and fuse-combination units
GOST IEC/TR 61912-2-2013: Low-voltage switchgear and control gear. Overcurrent protective devices. Part 2. Selectivity under over-current condition
GOST R 50030.3-2012: Low-voltage switchgear and control gear. Part 3. Switches, disconnectors, switch-disconnectors and fuse-combination units
GOST R 50030.4.1-2012: Low-voltage switchgear and control gear. Part 4. Contactors and motor-starters. Section 1. Electromechanical contactors and motor-starters
GOST R 50030.6.2-2011: Low-voltage switchgear and controlgear. Part 6-2. Multiple function equipment. Control and protective switching devices (or equipment) (CPS).
GOST R 50345-2010: Electrical accessories. Circuit-breakers for overcurrent protection for household and similar installations. Part 2. Circuit-breakers for a.c. operation
GOST R 50571.27-2003: Electrical installations of buildings. Part 7-740. Requirements for special installations or locations. Temporary electrical installations for structures, amusement devices and booths at fairgrounds, amusement parks and circuses
GOST R 50571.4.43-2012: Low-voltage electrical installations. Part 4-43. Protection for safety. Protection against overcurrent
GOST R 50571.7.722-2017: Low-voltage electrical installations. Part 7-722. Requirements for special installations or locations. Supplies for electric vehicles
GOST R 51327.1-2010: Residual current operated circuit-breakers with integral overcurrent protection for household and similar uses (RCBOs). Part 1. General rules and test methods
GOST R 55882.3-2013: Railway applications. Electric equipment for rolling stock. Part 3. Electrotechnical components. Rules for d.c. circuit-breakers
GOST R 55882.4-2013: Electric equipment of a railway rolling stock. Part 4. A.c. circuit-breakers. General specifications
GOST R 56124.5-2014: Renewable power engineering. Small renewable energy and hybrid systems for rural electrification. Recommendations. Part 5. Protection against electrical hazards
GOST R 56978-2016: Photovoltaic arrays. Specifications
GOST R 58320-2018: Electrical installation of traction power supply systems of the DC railway. Grounding Requirements
GOST R 58321-2018: Electrical installation of traction power supply systems of the AC railway. Grounding Requirements
GOST R 58408-2019: Electric networks of own needs and operating current of railway traction substations, transformer substations and linear devices of traction power supply system. Technical requirements, design rules, electrical calculation methods
GOST R 58409-2019: Unpackaged complete distribution devices for voltage up to 35 kV for traction and transformer substations of the railway. General specifications
GOST R 58604-2019: Unified energy system and isolated energy systems. Thermal power plants. Automated process control systems. Terms of creation. Norms and Requirements
GOST R ISO 22734-2-2014: Hydrogen generators using water electrolysis process. Part 2. Residential applications
Letter 15153/05-DG: About the application of the standards
Order 1317: The list of documents in the field of standardization, as a result of which, on a voluntary basis, compliance with the requirements of the Federal Law of July 22, 2008 No. 123-FZ "Technical Regulations on Fire Safety Requirements" is ensured
Order 832: The list of documents in the field of standardization, as a result of which, on a voluntary basis, compliance with the requirements of the Federal Law of July 22, 2008 No. 123-FZ "Technical Regulations on Fire Safety Requirements" is ensured
Protocol 03-14-PR: Meeting of the Working Group on making decisions on the possibility of using national and interstate standards developed on the basis of (instead of) previously valid, to ensure the activities of the Federal Accreditation Service (Rosakkreditatsiya) on accreditation and competence verification of accredited persons of April 29, 2022 N 03-14-pr
SP 323.1325800.2017: Residential areas. Urban and road lighting design
|
Customers Who Viewed This Item Also Viewed:
 |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Unified system for design documentation. Types and sets of design documentation
Language: English |
Loads and impacts
Language: English |
High strength rolled steel. General specification
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.
