GOST R IEC 60204-1-2007
ГОСТ Р МЭК 60204-1-2007
|
|
Safety of machinery. Electrical equipment of machines and mechanisms. Part 1. General requirements
Безопасность машин. Электрооборудование машин и механизмов. Часть 1. Общие требования
Status: Effective - Supersedes. IUS 5-2008
This standard applies to electrical and electronic systems and equipment for industrial machines and mechanisms that are not manually portable during their operation, including a group of machines working together in a consistent manner. This standard applies to electrical equipment and its parts operating on AC power at a nominal supply voltage of not more than 1000 V or DC not more than 1500 V between phases; nominal frequency range should be no more than 200 Hz
Настоящий стандарт распространяется на электрические и электронные системы и оборудование для непереносимых вручную во время их работы промышленных машин и механизмов, включая группу машин, работающих вместе в согласованном порядке. Настоящий стандарт распространяется на электрооборудование и его части, работающие от сети переменного тока при номинальном напряжении питания не более 1000 В или постоянного тока не более 1500 В между фазами; номинальный диапазон частот должен быть не более 200 Гц
Choose Language:
Format: Electronic (pdf/doc)
Approved: Federal Agency for Technical Regulation and Metrology,
12/27/2007
SKU: RUSS74306
The Product is Contained in the Following Classifiers:
Construction (Max) »
Standards »
Other state standards used in construction »
13 Environmental protection, protection of people from environmental exposure. Security »
Construction (Max) »
Standards »
Other state standards used in construction »
29 Electrical Engineering »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
004/2011 TR CU. About safety of low voltage equipment »
Regulations and standards (to TR CU 004/2011) »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
010/2011 TR CU. On safety of machinery and equipment »
Regulations and standards (to ТР ТС ТС 010/2011) »
Evidence base (TR CU, Technical Regulation of the Customs Union) »
038/2016 TR EAEU. About safety of rides »
Regulations and standards (to 038/2016 TR EAEC) »
PromExpert »
SECTION III. LABOR PROTECTION AND SAFETY »
III Occupational safety requirements for production equipment and processes »
2 Safety requirements for certain types of work »
2.2 Operation of production machines and equipment »
ISO classifier »
13 ENVIRONMENTAL PROTECTION, HUMAN PROTECTION AGAINST ENVIRONMENTAL IMPACT. SECURITY »
13.110 Safety of machinery »
National standards »
13 ENVIRONMENTAL PROTECTION, HUMAN PROTECTION AGAINST ENVIRONMENTAL IMPACT. SECURITY »
13.110 Safety of machinery »
ISO classifier »
29 ELECTRICAL ENGINEERING »
29.020 Electrical engineering in general »
National standards »
29 ELECTRICAL ENGINEERING »
29.020 Electrical engineering in general »
National Standards for KGS (State Standards Classification) »
Latest edition »
G Machines, equipment and tools »
G0 General rules and regulations for engineering »
G07 Safety »
As a Replacement Of:
GOST R IEC 60204-1-99: Safety of machinery. Electrical equipment of machines. Part 1. General requirements
The Document References:
GOST 14254-96: Degrees of protection provided by enclosures (IP Code)
GOST 28330-89: Asynchronous electrical machines with power from 1 to 400 kw inclusive. Motors
GOST 28690-90: Mark of conformity of technical means electromagnetic compatibility requirements. Form, sizes and technical requirements
GOST 29146.1-91: Plugs, socket-outlets
GOST 29149-91: Colours of indicator lights and push-buttons
GOST 30331.3-95: Electrical installations of buildings. Part 4. Protection for safety. Protection against electric shock
GOST 30331.5-95: Electrical installations of buildings. Part 4. Protection for safety. Protection against overcurrent
GOST R 50030.1-2007: Low-voltage switchgear and controlgear. Part 1. General rules
GOST R 50030.2-99: Low-voltage switchgear and controlgear. Part 2. Circuit-breakers
GOST R 50030.5.1-2005: Low-voltage switchgear and controlgear. Part 5. Control circuit devices and switching elements. Section 1. Electromechanical control circuit devices
GOST R 50030.7.1-2000: Low-voltage switchgear and controlgear. Part 7. Ancillary equipment. Section 1. Terminal blocks for copper conductors
GOST R 50571.10-96: Electrical installations of buildings. Part 5. Selection and erection of electrical equipment. Chapter 54. Earthing arrangements and protective conductors
GOST R 50571.15-97: Electrical installations of buildings
GOST R 50571.16-99: Electrical installations of buildings. Part 6. Verification. Chapter 61. Initial verification
GOST R 51321.1-2000: Low-voltage switchgear and controlgear assemblies. Part 1. Requirements for type-tested and partially type-tested assemblies. General technical requirements and methods of tests
GOST R IEC 60447-2000: Man-machine interface. Actuating principles
GOST R IEC 61140-2000: Protection against electric shock. Common aspects for installation and equipment
GOST R IEC 61557-3-2006: Low voltage distribution systems up to 1000 V a.c. and 1500 V d.c. Electrical safety. Equipment for testing, measuring or monitoring of protective measures. Part 3. Loop impedance
The Document is Referenced By:
Decision 295: About the Program for the development (amendment, revision) of interstate standards, the application of which on a voluntary basis ensures compliance with the technical regulations of the Customs Union "On the safety of low-voltage equipment" (TR TS 004/2011), as well as interstate standards containing rules and methods research (testing) and measurements, including sampling rules, necessary for the application and implementation of the requirements of the technical regulation of the Customs Union "On the safety of low-voltage equipment" (TR TS 004/2011) and the assessment of conformity of objects of technical regulation
GOST 10580-2006: Technological foundry equipment. General specifications
GOST 12.2.026.0-2015: Woodworking machinery. Construction safety requirements
GOST 12.2.026.0-93: Woodworking equipment safety requirements for design
GOST 12.2.124-2013: Occupational safety standards system. Alimentary product equipment. General safety requirements
GOST 12.2.231-2012: Occupational safety standards system. Polygraphic equipment. Safety requirements and test methods
GOST 22827-2020: Hoisting cranes. Self-propelled jib cranes. General technical requirements
GOST 31439-2011: Equipment and components intended for use in potentially explosive atmospheres in underground mines
GOST 31524-2012: Food processing machinery. Moulders. Specifications
GOST 31525-2012: Food processing machinery. Band saw machines. Specifications
GOST 31526-2012: Food processing machinery. Circular saw machines. Specifications
GOST 31527-2012: Food processing machinery. Intermediate provers. Specifications
GOST 31541-2012: Hammers. Safety requirements
GOST 31542-2012: Automatic and semi-automatic metal forming machines. Safety requirements
GOST 31595-2012: Log loaders. Knuckle boom equipment. General specifications
GOST 31606-2012: Rotating electrical machines. Asynchronous motors of power from 0,12 to 400 kW inclusive. General technical requirements
GOST 31733-2012: Hydraulic presses. Safety requirements
GOST 31839-2012: Pumps and pump units for pumping of liquids. General safety requirements
GOST 31840-2012: Submersible pumps and pump units. Safety requirements
GOST 32577-2020: Hoisting cranes. Portal cranes. General technical requirements
GOST 32617-2014: Irrigation machines. Safety
GOST 33662.2-2015: Refrigeration systems and heat pumps. The requirements of safety and environmental protection. Part 2. Design, construction, fabrication, testing, marking and documentation
GOST 33662.3-2017: Refrigerating systems and heat pumps. Safety and environmental requirements. Part 3. Installation site
GOST 33807-2016: Safety of attractions. General requirements
GOST 33938-2016: Definition of acceptable level (degree) of risk and hazard industry-wide manufacturing equipment
GOST 33966.1-2016: Escalators and moving walks. Safety requirements for construction and installation
GOST 34196-2017: Electrolyzers for the production of aluminum. General technical conditions
GOST 34682.1-2020: Lifting platforms for disabled people and other people with limited mobility. Safety requirements for device and installation. Part 1. Ladder and inclined platforms
GOST 34687-2020: Hoisting cranes. Rules and test methods
GOST 34891.2-2022: Refrigeration and heat pump systems. Safety and environmental requirements. Part 2. Design, construction, testing, labelling and documentation
GOST EN 1010-1-2016: Machines and equipment for printing. Safety requirements for design and manufacture. Part 1. General requirements
GOST EN 12001-2012: Conveying, spraying and placing machines for concrete and mortar. Safety requirements
GOST EN 12042-2013: Food processing machinery and equipment. Automatic dividers. Safety and hygiene requirements
GOST EN 12984-2013: Food processing machinery and equipment. Portable and/or hand-guided machines and appliances with mechanically driven cutting tools. Safety and hygiene requirements
GOST EN 13288-2013: Food processing machinery and equipment. Lifting and tilting machines. Safety and hygiene requirements
GOST EN 13389-2013: Food processing machinery and equipment. Mixers with horizontal shafts. Safety and hygiene requirements
GOST EN 13534-2013: Food processing machinery and equipment. Curing injection machines. Safety and hygiene requirements
GOST EN 13591-2013: Food processing machinery and equipment. Fixed deck oven loaders. Safety and hygiene requirements
GOST EN 13870-2013: Food processing machinery and equipment. Chop cutting machines. Safety and hygiene requirements
GOST EN 1501-2-2012: Refuse collection vehicles and associated lifting devices. General requirements and safety requirements. Part 2. Side loaded refuse collection vehicles
GOST EN 1672-1-2014: The equipment for the food industry. Requirements for safety and hygiene. The main provisions. Part 1. Safety requirements
GOST EN 1974-2013: Food processing machinery and equipment. Slicing machines. Safety and hygiene requirements
GOST EN 454-2013: Food processing machinery and equipment. Planetary mixers. Safety and hygiene requirements
GOST EN 536-2012: Road construction machines. Asphalt mixing plants. Safety requirements
GOST EN 574-2012: Safety of machinery. Two-hand control devices. Principles for design
GOST EN 809-2017: Pumps and pumping units for pumping liquids. General safety requirements
GOST EN 953-2014: Safety of machinery. Guards. General requirements for the design and construction of fixed and movable guard
GOST IEC 60947-5-3-2014: Low-voltage switchgear and controlgear. Part 5-3. Devices and switching elements of control circuits. Requirements for proximity devices with defined behaviour under fault conditions
GOST IEC 61496-1-2016: Safety of machinery. Electro-sensitive protective equipment. Part 1. General requirements and tests
GOST IEC 62135-1-2017: Resistance welding eguipment. Part 1. Safety reguirements for design, manufacture and installation
GOST ISO 21873-2-2013: Building construction machinery and equipment. Mobile crushers. Part 2. Safety requirements
GOST R 50030.5.5-2011: Low-voltage switchgear and control gear. Part 5-5. Control circuit devices and switching elements. Electrical emergency stop devices with mechanical latching function
GOST R 50030.5.8-2013: Low-voltage switchgear and control gear. Part 5-8. Control circuit devices and switching elements. Three-position enabling switches
GOST R 50571.27-2003: Electrical installations of buildings. Part 7-740. Requirements for special installations or locations. Temporary electrical installations for structures, amusement devices and booths at fairgrounds, amusement parks and circuses
GOST R 50571.7.717-2011: Low-voltage electrical installations. Part 7-717. Requirements for special installations or locations. Mobil or transportable units
GOST R 50786-2012: Metal-cutting household machine-tools. Safety requirements
GOST R 50803-2008: Food processing machinery. Tanks for cooling and storage of milk in milk-trade farms and reception stations. Technical requirements and safety parameters
GOST R 51101-2012: Metalworking and woodworking machines. Testing methods of compliance with safety requirements
GOST R 51321.1-2007: Low-voltage switchgear and control gear assemblies. Part 1. Type-tested and partially type-tested assemblies. General technical requirements and test methods
GOST R 51336-99: Safety of machinery. Emergency stop equipment. Functional aspects. Principles for design
GOST R 51345-99: Safety of machinery. Interlocking devices associated with guards. Principles for design and selection
GOST R 51838-2012: Safety of machinery. Electrical equipment for industrial machines. Test methods
GOST R 52291-2004: Log loaders. Knuckle boom equipment. General specifications
GOST R 52743-2007: Pumps and pump units for pumping of liquids. General safety requirements
GOST R 52744-2007: Submersible pumps and pump units. Safety requirements
GOST R 52776-2007: Rotating electrical machines. Rating and performance
GOST R 52915-2008: Automatic and semi-automatic metalforming machines. Safety requirements
GOST R 53010-2008: Hydraulic presses. Safety requirements
GOST R 53055-2008: Agricultural and forestry machinery with the electric drive. General safety requirements
GOST R 53130.1-2014: Safety of attractions. Part 1. Additional security requirements to the railrоаd
GOST R 53130.2-2014: Safety of attractions. Part 2. Additional security requirements to the driving ranges
GOST R 53130-2008: Safety of attractions. General requirements
GOST R 53140-2008: Food processing machinery. Intermediate provers. Specifications
GOST R 53463-2009: Hammers. Safety requirements
GOST R 53473-2009: Food processing machinery. Moulders Specifications
GOST R 53474-2009: Food processing machinery. Band saw machines. Specifications
GOST R 53475-2009: Food processing machinery. Circular saw machines. Specifications
GOST R 53476-2009: Food processing machinery. Cutting machines for meat. Specifications
GOST R 53477-2009: Food processing machinery. Dough and pastry brakes. Specifications
GOST R 53478-2009: Food processing machinery. Dough mixers. Specifications
GOST R 53481-2009: Lubrication systems. Safety requirements
GOST R 53543-2009: Aircraft and helicopter ground support equipment. General technical requirements
GOST R 53895-2010: Food processing machinery. Mincing machines. Safety and hygiene requirements
GOST R 53896-2010: Food processing machinery. Pasta processing dryers and coolers. Safety and hygiene requirements
GOST R 53942-2010: Food processing machinery. Clipping machines. Safety and hygiene requirements
GOST R 54111.3-2011: Fuel cell road vehicles. Safety engineering requirements. Part 3. Protection of persons against electric shock
GOST R 54125-2010: Safety of machinery and equipment. Principles for safety ensuring while designing
GOST R 54320-2011: Food processing machinery. Rotary rack ovens. Safety and hygiene requirements
GOST R 54321-2011: Food processing machinery. Centrifugal machines for processing edible oils and fats. Safety and hygiene requirements
GOST R 54371-2011: Safety in electric heating installations. Part 9. Particular requirements for high-frequency dielectric heating installations
GOST R 54387-2011: Food processing machinery. Dеrinding, skinning and membrane removal machines. Safety and hygiene requirements
GOST R 54388-2011: Food processing machinery. Pie and tart machines. Safety and hygiene requirements
GOST R 54406-2011: Ramps installed on vehicles for wheelchair users and for people restricted in their mobility. Safety requirements and testing
GOST R 54418.2-2014: Renewable power engineering. Wind power engineering. Wind turbines. Part 2. Design requirements for small wind turbines
GOST R 54418.24-2013: Renewable power engineering. Wind power engineering. Wind turbines. Part 24. Lightning protection
GOST R 54423-2011: Food processing machinery. Food processors and blenders. Safety and hygiene requirements
GOST R 54424-2011: Food processing machinery. Vegetable peelers. Safety and hygiene requirements
GOST R 54425-2011: Food processing machinery. Beam mixers. Safety and hygiene requirements
GOST R 54431-2011: Metal-working machines. General safety requirements
GOST R 54765-2011: Escalators and moving walks. Safety requirements for construction and installation
GOST R 54770-2011: Elevating work platforms. Mast-climbing work platforms. Calculating of structure, safely requirements, test methods
GOST R 54783-2011: Testing of agricultural machinery. Basic principles
GOST R 54967-2012: Food processing machinery and equipment. Сutters. Safety and hygiene requirements
GOST R 54968-2012: Food processing machinery. Mixing machines. Safety and hygiene requirements
GOST R 54969-2012: Food processing machinery and equipment. Equipment for pasta pressing. Safety and hygiene requirements
GOST R 54970-2012: Food processing machinery. Centrifugal devices for drying vegetables and fruits. Safety and hygiene requirements
GOST R 54971-2012: Food processing machinery. Spreaders, stripping and cutting machines, stick return conveyors, stick magazines. Safety and hygiene requirements
GOST R 54972-2012: Food processing machinery and equipment. Filling machines and auxiliary machines. Safety and hygiene requirements
GOST R 55178-2012: Cranes. Access, guards and restraints. Part 1. General
GOST R 55393-2012: Gas turbine power plant. Safety requirements
GOST R 55560-2013: Inland water transport. Operation of cargo transfer complexes and passenger terminals of river ports. Safety requirements. General
GOST R 55853-2013: Medium speed roller mill. Types, critical parameters, specification
GOST R 55968-2014: Escalators and moving walks. Improvement of safety of existing escalators and moving walks
GOST R 56188.2-2023: Fuel cell technology. Part 2. Fuel cell modules. Safety
GOST R 56188.3.100-2023: Fuel Cell Technologies. Part 3-100. Stationary fuel cell-based power plants. Safety
GOST R 56188.5.100-2023: Fuel Cell Technologies. Part 5-100. Portable fuel cell power plants. Safety
GOST R 57180-2016: Welding joints. Methods for determination of mechanical properties, macrostructure and microstructure
GOST R 57550-2017: Technological equipment for electron beam processing in vacuum
GOST R 57618.4-2017: Small craft infrastructure. Repair bases and services. General requirements
GOST R 58541.4-2019: Air conditioners, aggregated liquid coolers and heat pumps for heating and cooling rooms, technological chillers with electric compressors. Part 4. Requirements
GOST R 58585-2019: Mining equipment. General safety requirements for power supply and control systems
GOST R 58754-2019: Mobile scaffolds with a movable workplace. Technical specifications
GOST R 59208-2020: Machine tools safety. Stationary grinding machines
GOST R 59209-2020: Metal cutting machines. Security. Lathes
GOST R 59931-2021: Cranes for lifting. Requirements for electrical equipment
GOST R 60.0.2.1-2016: Robots and robotic devices. General requirements for safety
GOST R 60.1.2.1-2016: Robots and robotic devices. Safety requirements for industrial robots. Part 1. Robots
GOST R 60.1.2.2-2016: Robots and robotic devices. Safety requirements for industrial robots. Part 2. Robot systems and integration
GOST R 60.2.0.1-2022: (ISO 22166-1:2021) Robots and robotic devices. Modular principle of construction of service robots. Part 1. General requirements
GOST R 60.2.2.1-2016: Robots and robotic devices. Safety requirements for personal care robots
GOST R 60.2.3.1-2021: Robots and robotic devices. Personal care service robots. Safety test methods in accordance with the requirements of GOST R 60.2.2.1-2016
GOST R 60.6.3.14-2019: Robots and robotic devices. Performance and associated test methods for service mobile robots. Part 1. Movement of wheeled robots
GOST R 70298-2022: (ISO 19296:2018) Mining equipment. Self-propelled machines for underground mining operations. Safety requirements
GOST R 70301-2022: Low voltage systems. Cable Systems. Connectors and connectors. General requirements
GOST R 70514-2022: Electrical means of personal mobility. Technical requirements and test methods
GOST R 71237-2024: Suspended ropeways for transportation of people. Electrical equipment. Safety requirements
GOST R 71356-2024: Mining equipment. Bottom-hole machines. Safety requirements for mining harvesters and strings
GOST R EN 1010-1-2009: Printing machinery. Safety requirements for the design and construction. Part 1. General requirements
GOST R EN 1010-2-2011: Printing trades machinery. Safety requirements for the design and construction. Part 2. Printing and varnishing machines including pre-press machinery
GOST R EN 1034-1-2012: Paper-making and finishing machines. Safety requirements for the design and construction. Part 1. General requirements
GOST R EN 12750-2012: Safety of woodworking machines. Four sided planning (longitudinal and milling) machines
GOST R EN 12853-2012: Food processing machinery. Hand-held blenders and whisks. Safety and hygiene requirements
GOST R EN 13617-1-2012: Petrol filling stations. Part 1. Safety requirements for construction and performance of metering pumps, dispensers and remote pumping units
GOST R EN 14655-2012: Food processing machinery. Baguette slices. Safety and hygiene requirements
GOST R EN 1678-2012: Food processing machinery and equipment. Vegetable cutting machines. Safety and hygiene requirements
GOST R EN 1710-2009: Equipment and components intended for use in potentially explosive atmospheres in underground mines
GOST R EN 1870-1-2011: Safety of woodworking machines. Circular sawing machines. Part 1. Circular multipurpose saw benches (with and without sliding table), circular dimension saw and circular building site saws
GOST R EN 848-1-2011: Safety of woodworking machines. One side milling machines. Part 1. Single spindle milling machines with vertical lower arrangement of spindle
GOST R EN 859-2010: Safety of woodworking machines. Hand fed surface planning machines
GOST R EN 860-2010: Safety of woodworking machines. Outside thickness planning machines
GOST R EN 861-2011: Safety of woodworking machines. Surface planning and thickening machines
GOST R EN 940-2009: Safety of woodworking machines. Combined woodworking machines
GOST R IEC 60745-1-2009: Hand-held motor-operated electric tools. Safety and test methods. Part 1. General requirements
GOST R IEC 61784-3-12-2016: Industrial communications networks. Profiles. Part 3-12. Functional safety fieldbuses. Additional specifications for CPF 12
GOST R IEC 61784-3-3-2016: Industrial communications networks. Profiles. Part 3-3. Functional safety fieldbuses. Additional specifications for CPF 3
GOST R IEC 61784-3-8-2016: Industrial communications networks. Profiles. Part 3-8. Functional safety fieldbuses. Additional specifications for CPF 8
GOST R IEC 61800-1-2012: Adjustable speed electrical power drive systems. Part 1. General requirements. Rating specifications for low voltage adjustable speed d.c. power drive systems
GOST R IEC 61800-2-2012: Adjustable speed electrical power drive systems. Part 2. General requirements. Rating specifications for low voltage adjustable frequency a.c. power drive systems
GOST R IEC 61800-5-2-2015: Adjustable speed electrical power drive systems. Part 5-2. Functional safety requirements
GOST R IEC 62061-2015: Safety of machinery. Functional safety of safety-related electrical, electronic and programmable electronic control systems
GOST R IEC 62282-2-2014: Fuel cell technologies. Part 2. Fuel cell modules
GOST R IEC 62282-3-100-2014: Fuel cell technologies. Part 3-100. Stationary fuel cell power systems. Safety
GOST R IEC 62485-3-2013: Safety requirements for secondary batteries and battery installations. Part 3. Traction batteries
GOST R IEC 62485-3-2020: Rechargeable batteries and battery installations. Safety requirements. Part 3. Traction batteries
GOST R ISO 11161-2010: Safety of machinery. Integrated manufacturing systems. Basic requirements
GOST R ISO 11252-2016: Optics and photonics. Lasers and laser-related equipment. Laser device. Minimum requirements for documentation
GOST R ISO 12100-2-2007: Safety of machinery. Basic concepts, general principles for design. Part 2. Technical principles
GOST R ISO 22734-2-2014: Hydrogen generators using water electrolysis process. Part 2. Residential applications
GOST R ISO 23125-2012: Safety of machine tools. Turning machines
PNST 752-2022: Robots and robotic devices. Safety requirements. Part 1. Industrial robots
Customers Who Viewed This Item Also Viewed:
 |
Cylindrical evolvent gears of external engagment. Strength calculation
Language: English |
Unified system for design documentation. Types and sets of design documentation
Language: English |
Loads and impacts
Language: English |
High strength rolled steel. General specification
Language: English |
Food products, food raw materials. Method for determination of the non-steroidal anti-inflammatory drug residue content by high performance liquid chromatography – mass spectrometry
Language: English |
Articulated connector devices with cast male and female parts for freight cars of articulated type. General technical specifications
Language: English |
Plywood for general use with outer layers of deciduous veneer. Specifications
Language: English |
 |
|
YOUR ORDERING MADE EASY!
RussianGost.com is an industry-leading company with stringent quality control standards and our dedication to precision, reliability and accuracy are some of the reasons why some of the world’s largest companies trust us to provide their national regulatory framework and for translations of critical, challenging, and sensitive information.
Our niche specialty is the localization of national regulatory databases involving: technical norms, standards, and regulations; government laws, codes, and resolutions; as well as RF agency codes, requirements, and Instructions.
We maintain a database of over 220,000 normative documents in English and other languages for the following 12 countries: Armenia, Azerbaijan, Belarus, Kazakhstan, Kyrgyzstan, Moldova, Mongolia, Russia, Tajikistan, Turkmenistan, Ukraine, and Uzbekistan.
Placing Your Order
Please select your chosen document, proceed to the ‘checkout page’ and select the form of payment of your choice. We accept all major credit cards and bank wire transfers. We also accept PayPal and Google Checkout for your convenience. Please contact us for any additional arrangements (Contract agreements, PO, etc.).
Once an order is placed it will be verified and processed within a few hours up to a rare maximum of 24 hours.
For items in stock, the document/web link is e-mailed to you so that you can download and save it for your records.
For items out of stock (third party supply) you will be notified as to which items will require additional time to fulfil. We normally supply such items in less than three days.
Once an order is placed you will receive a receipt/invoice that can be filed for reporting and accounting purposes. This receipt can be easily saved and printed for your records.
Your Order Best Quality and Authenticity Guarantee
Your order is provided in electronic format (usually an Adobe Acrobat or MS Word).
We always guarantee the best quality for all of our products. If for any reason whatsoever you are not satisfied, we can conduct a completely FREE revision and edit of products you have purchased. Additionally we provide FREE regulatory updates if, for instance, the document has a newer version at the date of purchase.
We guarantee authenticity. Each document in English is verified against the original and official version. We only use official regulatory sources to make sure you have the most recent version of the document, all from reliable official sources.