Documents by Year

1930s (86)

1940s (117)

1950s (2)

1960s (844)

1970s (20003)

1980s (20684)

1990s (2216)

2000s (520)

2010s (44)

2020s (1)

2020 (1)

OST

«
1
…
8
9
10
11
12
13
14
…
52
»

Sealing of braided screen and spare wire ends with heat-shrinkable tubes and tapes. General provisions.

Removing the shield braid from the end of the wire. Typical process operation

Mechanically removing the insulation from the end of the wire. Typical process operation

Thermal shrinking of the tube using a heat electric fan. Typical process operation

Sealing of braided screen on wire ends with heat-shrinkable tubes without metallization. Typical operation of technological process.

Sealing of braided screen on wire ends with tapes and without metallization. Typical technological operation.

Sealing of braided screen on wire ends with heat-shrinkable tubes with metallization. Typical technological operation.

Sealing of braided screen on wire ends with tapes and metallization through a wire. Typical technological operation.

Sealing of a wire spare end with section up to 1 mm2, using heat-shrinkable tube. Typical technological operation.

Sealing of a wire spare end with section over 1 mm2, using heat-shrinkable tube. Typical technological operation.

Sealing of a wire spare end with section over 1 mm2, using heat-shrinkable tubes. Typical technological operation.

Sealing of a wire spare end with section over 1 mm2, using tape. Typical technological operation.

Automated process control systems for bench tests of gas turbine engines. Technical requirements

Unified system of technological documentation. Rules for processing technological documents for heat treatment in computer-aided design

Ultrasonic thickness gauge for monitoring the cast cooled blades of gas turbine engines. Test methods.

Melting of heat-resistant alloys and casting forms in vacuum furnaces such as UPPF. Typical process

Periodical rolling of HTE compressor blades of titanium and heat-proof alloys. Technical requirements.

Occupational safety standards system. Regulations and training of labour safety officers. General requirements.

Systems of automated programming of technological processes for CNC equipment. Input language. General provisions

OST 14-32-136-84

Cars of emergency services. Colour designs, identification marks. Technical requirements.

OST 14-4-138-84

Blanks evaluation for production of bolts and nuts by cold stamping method.

Conveyors. General Specifications.

Conductor for drilling holes in parts based on an epoxy resin cradle. Design and dimensions

Jig with clamping by adjustment plate. Design and dimensions.

Jigs with a movable prism. Design and dimensions.

Jigs with locating block, rotating about a horizontal axis. Design and dimensions.

Two-position rotary jig. Design and dimensions.

Jigs with a hinged presser bar. Design and dimensions.

Jigs with combined clamp.

Jigs with combined horizontal clamp.

Jig with a horizontal position of a base clamp and a clutch. Design and dimensions.

Jig with mutually perpendicular horizontal clamps to the vertical plane. Design and dimensions.

Jigs with a rotary disc and a movable centre. Design and dimensions.

Jigs with eccentric clamp. Design and dimensions.

Conductors bending at an angle of 90 degrees. Design and dimensions

Jigs canted for an angle of 60 degrees. Design and dimensions.

Jig with a horizontal clamp. Design and dimensions.

Jig with horizontal and vertical clamps. Design and dimensions.

Jig with wedge clamp, canted on a 90-degree angle. Design and dimensions.

Taps. Required dimensions. Restriction as per GOST 17039-71.

Taps. Thread tolerances. Restriction as per GOST 16925-71.

Round tapping die for metal thread. Thread Allowance. Restriction of GOST 17587-72.

Thread gauges to control metric thread according to OST 1 00105-83 with diameter of 1 to 200 mm.

Snap gauges for rods to form metric thread under OST 1 00105-83. Production dimensions.

Special stretch punches of asbestos cement boards. Types and main parameters.

Compound special stretch punches. Types and main parameters.

All-metal special stretch punches. Types and main parameters.

Special stretch punches of wood laminated plastic. Types and main parameters.

«
1
…
8
9
10
11
12
13
14
…
52
»

All Codes and Regulations

Codes	MGSN	OND	PR	SNiP	TU
Decisions	MI	ONTP	PUE	SN	VNTP
Decrees	MR	Orders	RD	SO	VPPB
GN	MSN	OST	RDS	SP	VRD
GOST	MSP	Other norms	Resolutions	ST SEV	VSN
Instructions	MUK	PB	RMU	STO
Laws	MU	PNAE	R	TI
Letters	ND	PND	RSN	TOI
MDK	NPB	POT	RTM	TR EAES
MDS	NP	PPB	SanPiN	TSN

All Categories

Construction (Max)	Highways (Max)	National Standards for KGS (State Standards Classification)	Power industry	Standards for pipe fittings (TPA)
Construction Price Formation	ISO classifier	National Standards for OKSTU	Projects of works (PPR) on bridges	Technical Supervision
Evidence base (TR CU, Technical Regulation of the Customs Union)	National standards	Organization Standards	PromExpert	Welding regulations

©RGTT 2016. All Rights Reserved.

Send us a message

Leave your message in the form below, and we will write back by e-mail!