Documents by Year

1930s (86)

1940s (117)

1950s (2)

1960s (844)

1970s (20003)

1980s (20684)

1990s (2216)

2000s (520)

2010s (44)

2020s (1)

2020 (1)

OST

«
1
…
4
5
6
7
8
9
10
…
12
»

Drilling of deep openings with a diameter from 5 to 15 mm by unilateral cutting with facing internal removal instruments. Standard technological operation.

Riveting with thermo-solid rivets of ГГД designs. Typical technological process.

Gauge-rings for metric thread with enlarged round-shaped vee, under OST 1 00105-83 with diameter from 4 to 200 mm. Dimensions.

OST 16 0.886.052-90

Printed circuit boards. Design requirements.

OST 16-0.510.065-90

Asynchronous electric machine with capacity more than 1 to 400 kW. , voltage up to 1000 V 3-phase asynchronous Freon -oil resistant built-in motors. General specifications.

OST 16-0.810.705-90

Electrical products. Collection, processing and distribution of information about the reliability of products. General provisions.

OST 16-0.886.052-90

Printed circuit boards. Design requirements

Taps for metric tapered threads in accordance with GOST 25229-82. Design

Round dies for metric tapered threads according to GOST 25229-82. Design

Working thread plug gauges Р-P to control metric tapered thread according to GOST 25229-82. Design.

Working thread ring gauges Р-P to control metric tapered thread according to GOST 25229-82. Design.

Control thread plug gauges K-P for cone thread ring gauges P-P with metric tapered thread according to GOST 25229-82. Design.

Working plain plug gauges Р-Г to control deviations in top cuts of metric tapered thread according to GOST 25229-82. Design.

Working smooth calibers-rings Р0Г for control of deviations of a cut of tops of a metric conic thread pl GOST 25229-82 Design

Control plain plug gauges К-Г for plain cone ring gauges P-Г for metric tapered thread according to GOST 25229-82. Design.

Plug gauges threaded two-sided PR (21) and NOT (22) to control the metric thread (fit fit) according to GOST 4608-81 Design

Plug gauges threaded through passage PR (34) to control the metric thread (fit with tension) according to GOST 4608-81. Design

Plug gauges threaded not HE (22) to control the metric thread (fit with fit) according to GOST 4608-81. Design

Plug gauges threaded sorting CP (35) for metric threads (fit with tension) according to GOST 4608-81. Design

Sorting thread plug gauges CP1 (36) for metric threads (interference fit) in accordance with GOST 4608-81. Design.

Sorting plug gauges СР2 (37) for metric threads (fit with tension) according to GOST 4608-81. Design

Smooth two-sided plug gauges PR (23) and NOT (24) to control the internal diameter of the metric thread (fit with fit) with tolerance fields 2Н50, 2Н50 (2), 2Н5С, 2Н5С (2) according to GOST 4608-81. Design

Two-sided plain plug gauges ПР (23) and HE (24) to control internal diameter of metric thread (interference fit) with tolerance margins 2Н40(3), 2Н4С(3) in accordance with GOST 4608-81. Design.

Footwear. Bottom details.

Industrial nylon belts.

Processing of injection molded thermosetting materials at press-molding machines. Typical process

Cutters from superhard cyboreth material. Sharpening and finishing. Typical process

Cutters from superhard cyboreth material. Cutting mode. Maintenance and repair

Rubber adhesives. Test methods. Viscosity test

Magnesium casting alloys. Heat Treatment Modes

Electrolytic solutions. General requirements for methods of analysis

Electrolyte solutions. Method of analysis of ammonium chloride electrolyte

Electrolyte solutions. Method of analysis of copper pyrophosphate electrolyte

Non-profiled welded rings of sheets, strips and plates of steel, special and titanium alloys. General technical conditions

Rings welded from sheets, strips and plates from special steel and titanium alloys, profiled by flanging. General technical conditions

Rings welded from hot-rolled sections from steels, special and titanium alloys rolled on SP 300 type mills. General technical conditions

Rings welded from sheet strips, profiled by rotational deformation. General technical conditions

Occupational safety standards system. Manufacturing fiberglass, honeycomb plastics and products based on them. General safety requirements

Electrolyte solutions. Acid electrolyte electrolyte analysis method

Electrolyte solutions. Ammonium Chloride Galvanizing Electrolyte Analysis Method

Electrolyte solutions. Acid Fluoride Oxide Electrolyte Analysis Method

Electrolyte solutions. Method of analysis of ammonium cadmium plating electrolyte

Electrolyte solutions. Chroming Electrolyte Analysis Method

Seamless rings made of steel sheet grade 12X18H10T, 12X18H107-Sh, profiled by rotational deformation. Technical conditions

Sheets of high impact polystyrene.

Sheets of high quality aluminum alloy brand AMg6. Technical conditions

AMg6 aluminum alloy high grade plates. Technical conditions

Extruded radius strip-shaped sections of aluminum alloys. Assortment

«
1
…
4
5
6
7
8
9
10
…
12
»

All Codes and Regulations

Codes	MGSN	OND	PR	SNiP	TU
Decisions	MI	ONTP	PUE	SN	VNTP
Decrees	MR	Orders	RD	SO	VPPB
GN	MSN	OST	RDS	SP	VRD
GOST	MSP	Other norms	Resolutions	ST SEV	VSN
Instructions	MUK	PB	RMU	STO
Laws	MU	PNAE	R	TI
Letters	ND	PND	RSN	TOI
MDK	NPB	POT	RTM	TR EAES
MDS	NP	PPB	SanPiN	TSN

All Categories

Construction (Max)	Highways (Max)	National Standards for KGS (State Standards Classification)	Power Industry	Standards for pipe fittings (TPA)
Construction Price Formation	ISO classifier	National Standards for OKSTU	Projects of works (PPR) on bridges	Technical Supervision
Evidence base (TR CU, Technical Regulation of the Customs Union)	National standards	Organization Standards	PromExpert	Welding regulations

©RGTT 2016. All Rights Reserved.

Send us a message

Leave your message in the form below, and we will write back by e-mail!