Documents by Year
1930s (86)
1940s (117)
1950s (2)
1960s (844)
1970s (20003)
1980s (20684)
1990s (2216)
2000s (520)
2010s (44)
2020s (1)
Other (744)

OST

OST 3-4813-80
OST 3-4813-80
Short-stroke double-acting hydraulic cylinders with foot mounting for nominal pressure of 10 MPa (100 kg/cm2). Construction and dimensions.
OST 3-4814-80
OST 3-4814-80
Pistons. Design and dimensions.
OST 3-4815-80
OST 3-4815-80
Assembly pistons. Design and dimensions.
OST 3-4816-80
OST 3-4816-80
Hydraulic Cylinders. General technical requirements.
OST 3-4817-80
OST 3-4817-80
Single-sided straps with built-in hydraulic cylinder. Design and dimensions.
OST 3-481-80
OST 3-481-80
Thread-cutting flat combs. Types, construction, dimensions and technical requirements
OST 3-4818-80
OST 3-4818-80
Self-setting hydraulic support. Design and dimensions.
OST 3-4819-80
OST 3-4819-80
Hydraulic clamps. Design and dimensions.
OST 3-4820-80
OST 3-4820-80
L-shaped hydraulic rotary straps. Design and dimensions.
OST 3-4821-80
OST 3-4821-80
Adjustment packings. Design and dimensions.
OST 3-4822-80
OST 3-4822-80
Movable hydraulic strap. Design and dimensions.
OST 3-4823-80
OST 3-4823-80
Hydraulic clamps. Design and dimensions.
OST 3-4824-80
OST 3-4824-80
Hydraulic straps with step block. Design and dimensions.
OST 3-4825-80
OST 3-4825-80
Pneumatic actuators with reinforced link. Design and dimensions.
OST 3-4826-80
OST 3-4826-80
Hydraulic accumulator few-group Installation. Design and dimensions.
OST 3-4827-80
OST 3-4827-80
Hydraulic accumulator Installation. Design and dimensions.
OST 3-4828-80
OST 3-4828-80
Hydraulic control panels. Construction and dimensions.
OST 3-4829-80
OST 3-4829-80
Hydraulic four-position six way control valve for nominal pressure 100 MPa (100 kgf/cm2) and GN 10mm. Design and dimensions.
OST 3-4830-80
OST 3-4830-80
Thermal vacuum chambers. Safety requirements during exploitation.
OST 3-4832-80
OST 3-4832-80
Equipment for casting machines under pressure. Bearings of crucibles for induction melting. Classification, design and dimensions.
OST 3-4833-80
OST 3-4833-80
Equipment for casting machines under pressure. Die moulds. Design and dimensions.
OST 3-4836-80
OST 3-4836-80
Cold die close tolerance stamping. Ensuring manufacturability of thin sheet parts. Main provisions.
OST 3-4840-80
OST 3-4840-80
Pneumatic actuator movable deadhead sleeves. Design and dimensions. Technical requirements.
OST 3-4841-80
OST 3-4841-80
Piston pneumatic actuators. Design and dimensions. Technical requirements.
OST 3-4842-80
OST 3-4842-80
Build-in cylinders. Design and dimensions. Technical requirements.
OST 3-4843-80
OST 3-4843-80
Tap build-in cylinders. Design and dimensions. Technical requirements.
OST 3-4844-80
OST 3-4844-80
Stem seals. Design and dimensions. Technical requirements .
OST 3-4845-80
OST 3-4845-80
Pistons. Design and dimensions. Technical requirements.
OST 3-4846-80
OST 3-4846-80
Reinforced pistons. Design and dimensions. Technical requirements.
OST 3-4847-80
OST 3-4847-80
On-off control valve with nominal diameter equal 5 mm. Design and dimensions. Technical requirements.
OST 3-4848-80
OST 3-4848-80
On-off control valve with nominal diameter equal 8 mm. Design and dimensions. Technical requirements.
OST 3-4849-80
OST 3-4849-80
Built-in on-off control valve. Design and dimensions. Technical requirements.
OST 3-4850-80
OST 3-4850-80
Three-way control valve. Design and dimensions. Technical requirements.
OST 3-4851-80
OST 3-4851-80
Cylinders. Design and dimensions. Technical requirements.
OST 3-4852-80
OST 3-4852-80
Cylinders with grooves for sealing. Design and dimensions. Technical requirements.
OST 3-4853-80
OST 3-4853-80
Caps. Design and dimensions. Technical requirements.
OST 3-4854-80
OST 3-4854-80
Caps with a connecting location for a valve. Design and dimensions. Technical requirements.
OST 3-4855-80
OST 3-4855-80
Rods-wedges. Design and dimensions.Technical requirements .
OST 3-4856-80
OST 3-4856-80
Rods-wedges with double angle of wedge. Design and dimensions.Technical requirements .
OST 3-4857-80
OST 3-4857-80
Rods-wedges with rectangular cross-section of wedge. Design and dimensions.Technical requirements .
OST 3-4858-80
OST 3-4858-80
Rods-wedges with hole. Design and dimensions.Technical requirements .
OST 3-4859-80
OST 3-4859-80
Annular rubber rings of T-shaped cross section for pneumatic devices. Design and dimensions. Technical requirements.
OST 3-4860-80
OST 3-4860-80
Check valves. Design and dimensions.
OST 3-4861-80
OST 3-4861-80
Direct end flare joints. Construction and dimensions.
OST 3-4862-80
OST 3-4862-80
Threaded bushing pipe joint. Construction and dimensions.
OST 3-4863-80
OST 3-4863-80
End connections for hose pipes. Construction and dimensions. Technical requirements.
OST 3-4864-80
OST 3-4864-80
Detached end connections for hose pipes. Construction and dimensions.
OST 3-4865-80
OST 3-4865-80
Hose pipe adapting joints. Construction and dimensions.

All Codes and Regulations

Codes MGSN OND PR SNiP TU
Decisions MI ONTP PUE SN VNTP
Decrees MR Orders RD SO VPPB
GN MSN OST RDS SP VRD
GOST MSP Other norms Resolutions ST SEV VSN
Instructions MUK PB RMU STO
Laws MU PNAE R TI
Letters ND PND RSN TOI
MDK NPB POT RTM TR EAES
MDS NP PPB SanPiN TSN

All Categories

Construction (Max) Highways (Max) National Standards for KGS (State Standards Classification) Power Industry Standards for pipe fittings (TPA)
Construction Price Formation ISO classifier National Standards for OKSTU Projects of works (PPR) on bridges Technical Supervision
Evidence base (TR CU, Technical Regulation of the Customs Union) National standards Organization Standards PromExpert Welding regulations

Send us a message Expand Collapse

Leave your message in the form below, and we will write back by e-mail!